This exhaust band clamp kit from Innovate Motorsports is engineered to work with their Type K thermocouple EGT probes on applications where it is not possible to weld conventional mounting bosses.

• Includes #32 Clamp (1 9/16" -2 1/2" ), Nut, Brass Ferrule & Base.

This Stainless Steel Adapter Allows You To Use A Full Size 18Mm Thread O2 Sensor In A 12Mm Original Equipment Bung. Most Import Motorcycles, Atvs Etc. Come With A 12Mm O2 Sensor. This Adapter Allows You To Use One Of Innovates Data Loggers Or Gauges Without The Need Of Welding In A New Bung. This Adapter Allows Mounting The O2 Sensor At A 45-Degree Angle. The Nut Allows You To Point The Adapter In Any Direction For The Greatest Amount Of Clearance.

• Copper sealing washer included (not pictured).

The Bosch LSU4.2 and LSU4.9 wide-band O2 sensors (shipped standard with Innovate Motorsport products) are rated to operate at an exhaust gas temperature of < 1,700 Fahrenheit (930 Celsius), and a sensor housing temperature of < 1,058 Fahrenheit (570 Celsius) measured at the hex, for maximum accuracy and control. When either of these operating temperature ranges is exceeded, the sensor can no longer be accurately controlled. Further, operating at or above these temperatures for any length of time can significantly reduce the life expectancy of the sensor. Innovate Motorsports products are designed to display an error message under these conditions (08- Sensor Timing Error) rather than provide inaccurate readings. For some turbo vehicles, rotary engines, and other specialty setups, this error message can be encountered with annoying frequency due to operating conditions specific to those engine types and configurations. This precision machined part is engineered to address applications generating excessive heat in the O2 sensor by utilizing a specialty heat sink design which pulls the sensor futher out of the exhaust stream while maintaining correct flow of exhaust gasses to the sensor for accurate readings.

• Specialized heat-sink design pulls sensor 1.1875" (30mm) out of original weld boss, reducing applied temperature to the sensor while maintaining critical flow of exhaust gasses to the sensing element for accurate readings.

The all-new 6th Generation Ford Bronco is an amazing vehicle that comes from the factory ready to tackle the world. That said, there are a few design flaws that limit the amazing ability the Bronco has to offer. One of those flaws is the reduced approach and departure angle from the oversize stock muffler and low hanging exhaust tip. Injen has recognized this issue and has an affordable solution that allow you not only improve your approach and departure angles, but also improve performance and completely change the sound of your Bronco!

• Note: This part is not an emissions-related part and therefore can be used on Emission Controlled Vehicles without a CARB EO#
• Oversized tubing reduces restriction providing increased airflow and performance
• Fast and simple bolt-on that provides increased approach and departure angles
• Manufactured from huge 3.0in (76mm) mandrel-bent 304 stainless-steel tubing
• Straight through, single exit design developed for maximum exhaust flow
• Includes high quality band clamps for a simple, leak-free installation
• Hand Crafted and TIG Welded to Perfection for Strength and Durability
• Injen's Muffler Delete Kit replaces the restrictive factory muffler.
• Uses all factory mounting locations with factory-style hangers
• Fits both 2-door and 4-door models without modifications
• Dyno Proven gains of up to 8 hp and 10 lb-ft. of torque
• Increase Throttle Response and Decreases Turbo Lag
• High-tuck design for increased ground clearance
• Designed and manufactured in Pomona, CA
• EMISSIONS

This Part Fits:

Being able to have increased clearance is nice, but let's face it, we all buy exhaust systems to improve the sound of our vehicle and Injen Technology doesn't disappoint! The Injen Technology engineers designed a custom dual muffler system that would provide great sound with the both the L4-2.7 Turbo and also the V6-2.7L Twin Turbo, which is no easy feat. The SES9300AB exhaust system is also made from mandrel-bent 304 stainless steel and not the lesser quality 409 Stainless like our competition uses. This provides you with an exhaust that not only looks great, but will last you a lifetime.

• Note: This part is not an emissions-related part and therefore can be used on Emission Controlled Vehicles without a CARB EO#
• High Tuck design for increased ground clearance on approach and departure angles
• Oversized tubing reduces restriction providing increased airflow and performance
• Custom investment cast Y-Pipe equalizes flow for improved performance and sound
• Includes Injen's dual oval, straight-through mufflers for our signature sound
• Manufactured from huge 3.0in (76mm) mandrel-bent 304 stainless-steel tubing
• Can be used with the stock exhaust OR with Injen's Mid-Pipe P/N: SES9300MP
• Hand Crafted and TIG Welded to Perfection for Strength and Durability
• Uses all factory mounting locations with factory-style hangers
• Includes all necessary hardware for a hassle-free installation
• Tip extensions can be removed for improved departure angle
• Fits both 2-door and 4-door models without modifications
• Dyno Proven gains of up to 9 hp and 10 lb-ft. of torque
• Dual 4.0in (101.6mm) bolt-on black ceramic exhaust tips
• Increase Throttle Response and Decreases Turbo Lag
• High-tuck design for increased ground clearance
• Injen Technology Limited Lifetime Warranty
• Designed and manufactured in Pomona, CA
• Axle-Back design
• EMISSIONS

This Part Fits:

The Injen Technology exhaust system for the Jeep Gladiator features full 3" mandrel bent 304 stainless steel tubing that provides optimal pipe routing for maximum flow and additional clearance for extreme off-road use. That 3" piping flows directly into our Injen oval muffler that was designed specifically for the new Jeep powerplants. Our Jeep specific muffler is shallow in height to provide increased ground clearance, all while having the correct interior volume and design to tame the exhaust note of the mighty Jeep Gladiator. Delivering a smooth, deep tone that is distinct to the Injen exhaust line, this system provides you with all dyno-proven performance you crave and the sound enhancements that you demand.

• Features Injen's low-profile oval muffler to deliver a clean, crisp, distinctively Injen sound
• If you're looking to improve sound, power, and looks then this is the system for you!
• Exhaust exits at the OE location for endless bumper and suspension options
• Hand Crafted and TIG Welded to Perfection for Strength and Durability
• Full 76MM piping made from premium 304 SS Mandrel-Bent Tubing
• Pairs perfectly with our cold air intake EVO5005 and EVO5005C
• Unique Muffler Designed Specifically for the Jeep JK/JL/JT
• Injen's legendary Single exit, high-tuck, cat-back design
• Dyno Proven gains of up to 5 hp and 5 lb-ft. of torque
• Show Quality Embossed Stainless Steel Muffler
• Premium Stainless Steel Hardware and Hangers
• Designed And Made In Pomona; CA
• Designed and Made in Pomona, CA
• No Cutting or Welding Required

This Part Fits:

The all new Jeep Wrangler JL has taken the world by storm. Even with the increased performance and outstanding off road capabilities, you're still looking for more. Look no further because the Injen Technology engineers are experts when it comes to performance, PERIOD. They have already designed the best cold air intake (EVO5005) and snorkel system (EVO15168) on the market and they've followed that up with this beautiful high tuck, single outlet, axle back exhaust system for the Wrangler JL. , , This new SES5006AB high tuck axle back exhaust system for the Jeep Wrangler JL sits high and inside the chassis for increased approach and decent angles during those extreme off road adventures. You no longer have to worry about smashing your exhaust system or ripping the exhaust tip off!, , Being able to have increased clearance is nice, but let's face it, we all buy exhaust systems to improve the sound our vehicle makes and Injen Technology doesn't disappoint! The Injen Technology engineers designed a custom muffler that would provide great sound with the 3.6L and the 2.0L Turbo engine, which is no easy feat. The SES5006AB exhaust system is also made from mandrel-bent 304 stainless steel and not the lesser quality 409 like our competition uses. This provides you with an exhaust that not only looks great, but will last you a lifetime. , , Plain and simple, NUMBERS talk! Injen has a strong legacy of designing and thoroughly testing every product we develop and the SES5006AB clearly benefits from our dedication to performance. Our engineers put in countless hours of testing to prove that we have developed the safest, highest performing exhaust system on the market. With a proven 8 additional horsepower and 8 Lbs-Ft. of torque, Injen is proud to say that the SES5006AB exhaust system is the very best high tuck exhaust for your Jeep Wrangler JL that money can buy.

• Features Injen's low-profile oval muffler to deliver a clean, crisp, distinctively Injen sound
• High Tuck design for increased ground clearance, approach and departure angles
• Show Quality, Injen Embossed, Low Profile, Oval Stainless Steel Muffler
• Hand Crafted and TIG Welded to Perfection for Strength and Durability
• Also available - Injen Evolution Cold Air Intake EVO5005 / EVO5005C
• Full 76MM piping made from premium 304 SS Mandrel-Bent Tubing
• Also available - Injen X-Pedal Pro Throttle Controller PT0010
• Injen's legendary High Tuck, Single Outlet, Axle Back design
• Dyno Proven gains of up to 8 hp and 8 lb-ft. of torque
• Fits both 2-Door and 4-Door Wrangler JL models.
• Also available - Injen Snorkel System EVO15168
• Injen Technology Limited Lifetime Warranty
• Hand Crafted And TIG Welded To Perfection
• Made in Pomona California, USA

This Part Fits:

The Jeep Wrangler is an amazing vehicle that comes from the factory ready to tackle the world. That said, there are a few design flaws that limit the amazing ability the Wrangler has to offer. One of those flaws is the reduced approach and departure angle from the oversize stock muffler and low hanging exhaust tip. Injen has recognized this issue and has an affordable solution that allow you not only improve your approach and departure angles, but also improve performance and completely change the sound of your JK!, , SES5003MD is our newest muffler delete kit for the 2007-2018 Jeep Wrangler JK (3.6L & 3.8L) and is a fantastic solution for those that want to climb those steeper obstacles without breaking the bank on a high tuck exhaust. In fact, you can easily swap over to this muffler delete for the weekend wheeling trips and then reinstall your OE muffler for your weekly commute ? all within 20 minutes. This isn't our cheap delete kit made from thin cold-rolled steel that will either rust or crack, the Injen Muffler Delete kit is made for 304 stainless steel that is mandrel bent right here in Pomona, CA for durable, long-lasting performance. During the design process, our engineers made sure that the install was a simple as possible and retained the use of the factory hanger locations. This allows for quick swaps without throwing any wrenches!, , As always, the SES5003MD muffler delete works seamlessly with our full line of Jeep performance products. From Rotomolded air intakes to throttle response controllers to complete performance exhaust systems, Injen Technology is here to help you take on the world in your Jeep!

• Injen's Muffler Delete Kit replaces the restrictive factory muffler and exhaust pipe.
• Simple Bolt-on Installation using factory mounting points with no cutting or welding
• Smooth pipe routing eliminates restrictions and greatly improves airflow
• Injen Intake also available ? EVO5002 (3.8L) and EVO5003 (3.6L)
• Aggressive engine tone, especially under full throttle
• Injen X-Pedal Throttle Response Controller ? PT0013
• Provides increased approach and departure angles
• Made From Mandrel Bent 60mm 304 Stainless Steel
• Injen Snorkel also available - EVO15070
• Made in Pomona California, USA
• No additional tuning required
• Uses Factory Hanger

This Part Fits:

The SES3078TIP has a larger internal diameter to give your turbo free access to as much air as it can ever need. It is also designed with smooth airways to minimize turbulence and keep drag from fighting against your turbo's compressor. This simple change alone also increased the sound output of the turbo, giving you both tangible and audible performance gains. On our quest to make this part as durable as humanly possible, we have integrated the PCV Inlet as well as the mounting arm into the Unibody Cast Aluminum housing.

• Complementing Injen Cold Air Intakes, Throttle Controllers, and Intercooler Charge Pipes available for various VW/Audi Applications. Check the Injen Application guide for your specific application.
• Note: This product is not currently CARB exempt and is not available for purchase in California or for use on any vehicle registered with the California Department of Motor Vehicles.
• Fits directly in place of the OEM component, maximizing compatibility with other OEM and aftermarket components.
• Fully integrated Mounting Bracket minimizes the chance of mounting hardware loosening over time.
• 3? Inlet OD minimizes turbulence and allows the maximum amount of air to reach the turbo.
• Provides faster turbo spool, increased responsiveness, and greater turbo sound output.
• 3? Reinforced Silicon Automotive Grade Coupler included for increased longevity.
• Cast Aluminum Housing offers far superior durability over OEM plastic component.
• Precision CNC Machined Fittings for a superior seal and simple installation.
• Fully integrated CNC Machined PCV Inlet provides an OE fitment and seal.
• Includes the industry leading Injen Limited Lifetime Warranty.
• Dyno Proven Gains of up to 14 hp and 11 lb-ft. of torque.
• Stainless Steel Band Clamps with Inner Protective Liner.
• This product will only work with 3.00" diameter tubing
• Simple Installation, no cutting or drilling required.

This Part Fits:

The legendary Toyota Supra has returned for 2020! A legend only deserves the best and the Injen Race Series Cat-Back Single-Exit Exhaust System Delivers! Specifically engineered for the 2020-2025 Toyota GR Supra equipped with the L6-3.0L Turbo, this system was designed from the ground up to compliment the aggressive styling and blistering performance of these sporty sedans. Our race inspired single-exit design hones the tone of the engine into an ear-pleasing symphony. Purposefully delivering a crisp, clean, deep rumble at idle and an aggressive roar when you're pushing the limits.

• NOTE: This part is not an emissions-related part and therefore can be used on Emission Controlled Vehicles without a CARB EO#.
• Race Exhaust design that eliminates all factory mufflers, resonators, and valves for race inspired weight reduction and sound
• No-tip racing design that utilizes oversized 3.50in tubing the entire length of the exhaust
• Dyno Proven power increase of 10 HP and 11 Lb.-Ft. of torque at the wheels
• Hand Crafted and TIG Welded to Perfection for Strength and Durability
• A savings of over 20lbs when compared to the stock exhaust system!
• Beautiful V-Band clamps used for a simple, leak-free installation
• Manufactured from huge, mandrel-bent, 304 stainless-steel tubing
• Uses all factory mounting locations with factory-style hangers
• Includes all necessary hardware for a hassle-free installation
• Increase Throttle Response and Decreases Turbo Lag
• Designed and manufactured in Pomona, CA
• Race-Inspired single exit design
• Emissions

This Part Fits:

We design every performance product with ease of installation in mind and this exhaust is no different. On the SES2300CF we've included V-Band clamps and flanges for the simplest, quickest installation possible. No need for any cutting, drilling, or modification of the vehicle to complete installation. The system uses all factory mounting points for simple and convenient placement and compatibility. To increase performance, we opted for a stepped piping design that keeps the flow rate consistent throughout the length of the exhaust. Keeping the flow rate consistent not only adds performance but also helps keep the tone of the exhaust where we designed it to be throughout the rev range.

• Emissions: This part is not an emissions-related part and therefore can be used on Emission Controlled Vehicles without a CARB EO#.
• Integrated exhaust valve for normal (quiet) and sport mode (race inspired sound) operation
• Injen's dual oval, straight-through mufflers for exceptional sound and power output
• Oversized tubing reduces restriction providing increased airflow and performance
• Custom investment cast Y-Pipe equalizes flow for improved performance and sound
• Dyno Proven power increase of 11 HP and 9 Lb.-Ft. of torque at the wheels
• Hand Crafted and TIG Welded to Perfection for Strength and Durability
• Beautiful V-Band clamps used for a simple, leak-free installation
• Manufactured from huge, mandrel-bent, 304 stainless-steel tubing
• Performance Stepped design for maximum performance and velocity
• Uses all factory mounting locations with factory-style hangers
• Includes all necessary hardware for a hassle-free installation
• Front and mid-section utilizing massive 3.50in (89mm) tubing
• Dual 4.5in (114mm) bolt-on Carbon Fiber Exhaust Tips
• Increase Throttle Response and Decreases Turbo Lag
• Rear section utilizes huge 3.00in (76mm) tubing
• Exhaust Valve uses factory motor: not included
• Designed and manufactured in Pomona, CA

This Part Fits:

The Injen Technology engineers are experts when it comes to performance, PERIOD. From Cars to Trucks to Powersports, Injen has a variety of exhaust systems to choose from. All of Injen Technology Performance exhaust systems are constructed from mandrel bent stainless steel tubing Mandrel-bending ensures the tubing maintains its shapes and size throughout the entire length, providing smooth, unrestricted airflow. From the Investment cast flanges to the custom hangers, all Injen exhaust systems are 100% TIG welded and handcrafted in the USA and include all tubing, mufflers, and hardware necessary for a hassle free installation. Each system is uniquely designed to offer an aggressive sound that brings out some massive power. Like all other Injen products, the Injen exhaust systems are proudly built in Pomona, CA.

• Features Injen's JDM Style round muffler to deliver a clean, crisp, distinctively Injen sound
• If you're looking to improve sound, power, and looks then this is the system for you!
• Hand Crafted and TIG Welded to Perfection for Strength and Durability
• Stainless Steel Investment Cast Flange for a Fast and Easy Install
• Premium Stainless Steel Hardware and Hangers for a simple install
• Full 60MM piping made from premium 304 SS Mandrel-Bent Tubing
• Injen's legendary Performance Axle-Back exhaust system
• Dyno Proven gains of up to 7 hp and 7 lb-ft. of torque
• Designed and Manufactured in Pomona, CA
• Beautiful 4.5"polished exhaust tip
• No Cutting or Welding Required
• Cat Located At Rear of Axle

This Part Fits:

The Injen Technology engineers are experts when it comes to performance, PERIOD. From Cars to Trucks to Powersports, Injen has a variety of exhaust systems to choose from. All of Injen Technology Performance exhaust systems are constructed from mandrel bent stainless steel tubing Mandrel-bending ensures the tubing maintains its shapes and size throughout the entire length, providing smooth, unrestricted airflow. From the Investment cast flanges to the custom hangers, all Injen exhaust systems are 100% TIG welded and handcrafted in the USA and include all tubing, mufflers, and hardware necessary for a hassle free installation. Each system is uniquely designed to offer an aggressive sound that brings out some massive power. Like all other Injen products, the Injen exhaust systems are proudly built in Pomona, CA.

• Features Injen's dual JDM Style round mufflers to deliver a clean, crisp, distinctively Injen sound
• If you're looking to improve sound, power, and looks then this is the system for you!
• Fits RWD Coupe Models Only. Excludes G37X AWD and Rear Active Steering models
• Injen's fully functional upstream resonator with integrated internal X-Pipe
• Hand Crafted and TIG Welded to Perfection for Strength and Durability
• True dual exhaust made from premium 60MM 304 SS Mandrel-Bent Tubing
• Stainless Steel Investment Cast Flange for a Fast and Easy Install
• Premium Stainless Steel Hardware and Hangers for a simple install
• Injen's legendary Full Performance Cat-Back exhaust system
• Dyno Proven gains of up to 14 hp and 16 lb-ft. of torque
• Resonated Titanium Dual Wall Rolled-Burnt Tips
• Beautiful dual 4.5"titanium exhaust tips
• Designed and Manufactured in Pomona, CA
• No Cutting or Welding Required

This Part Fits:

Pump up the volume in that Sentra of yours, exhaust volume that is! The Injen Sentra exhaust has an overall diameter of 60mm to provide you with a subdued yet aggressive exhaust note. That 1.6L turbo under the hood of your Sentra will thank you, for letting it be heard. The SES1971 Cat-back exhaust system will help beef up the exhaust tone but still helps to pull the sound back a bit to prevent drone when at cruising speed. Our 2017 Nissan(R) Sentra exhaust is constructed completely of mandrel-bent 304 stainless steel, for smooth exhaust flow and maximum durability. You won't have to worry about this exhaust rusting out and plaguing your system with exhaust leaks. The Injen Sentra Cat-back exhaust provides a clean look, is finished off with a 3.5" single wall rolled polished tip. Installation can be accomplished in under one hour to get your Sentra back on the road in no time. Combine this Cat-back exhaust with our Sentra cold air intake for a complete performance package. The Injen Limited Lifetime Warranty guarantees precision craftsmanship, to keep your Sentra looking and sounding good.

• Features Injen's JDM Style round muffler to deliver a clean, crisp, distinctively Injen sound
• If you're looking to improve sound, power, and looks then this is the system for you!
• Hand Crafted and TIG Welded to Perfection for Strength and Durability
• Stainless Steel Investment Cast Flange for a Fast and Easy Install
• Premium Stainless Steel Hardware and Hangers for a simple install
• Full 76MM piping made from premium 304 SS Mandrel-Bent Tubing
• Dyno Proven gains of up to 8 hp and 7 lb-ft. of torque
• Does NOT work with SES1971 full exhaust system
• Backed By Injens Limited Lifetime Warranty
• Designed and Manufactured in Pomona, CA
• Performance Axle Back exhaust system
• Beautiful 4.0"polished exhaust tip
• No Cutting or Welding Required

This Part Fits:

Pump up the volume in that Sentra of yours, exhaust volume that is! The Injen Sentra exhaust has an overall diameter of 60mm to provide you with a subdued yet aggressive exhaust note. That 1.6L turbo under the hood of your Sentra will thank you, for letting it be heard. The SES1971 Cat-back exhaust system will help beef up the exhaust tone but still helps to pull the sound back a bit to prevent drone when at cruising speed. Our 2017 Nissan(R) Sentra exhaust is constructed completely of mandrel-bent 304 stainless steel, for smooth exhaust flow and maximum durability. You won't have to worry about this exhaust rusting out and plaguing your system with exhaust leaks. The Injen Sentra Cat-back exhaust provides a clean look, is finished off with a 3.5" single wall rolled polished tip. Installation can be accomplished in under one hour to get your Sentra back on the road in no time. Combine this Cat-back exhaust with our Sentra cold air intake for a complete performance package. The Injen Limited Lifetime Warranty guarantees precision craftsmanship, to keep your Sentra looking and sounding good.

• Features Injen's 12in Long resonator to deliver a clean, crisp, distinctively Injen sound
• If you're looking to improve sound, power, and looks then this is the system for you!
• Hand Crafted and TIG Welded to Perfection for Strength and Durability
• Stainless Steel Investment Cast Flange for a Fast and Easy Install
• Premium Stainless Steel Hardware and Hangers for a simple install
• Full 76MM piping made from premium 304 SS Mandrel-Bent Tubing
• Dyno Proven gains of up to 14 hp and 12 lb-ft. of torque
• Backed By Injens Limited Lifetime Warranty
• Full Performance Cat-Back exhaust system
• Designed and Manufactured in Pomona, CA
• Does NOT work with SES1971AB Axle Back
• Beautiful 4.0"polished exhaust tip
• No Cutting or Welding Required

This Part Fits:

The Injen Technology engineers are experts when it comes to performance, PERIOD. From Cars to Trucks to Powersports, Injen has a variety of exhaust systems to choose from. All of Injen Technology Performance exhaust systems are constructed from mandrel bent stainless steel tubing Mandrel-bending ensures the tubing maintains its shapes and size throughout the entire length, providing smooth, unrestricted airflow. From the Investment cast flanges to the custom hangers, all Injen exhaust systems are 100% TIG welded and handcrafted in the USA and include all tubing, mufflers, and hardware necessary for a hassle free installation. Each system is uniquely designed to offer an aggressive sound that brings out some massive power. Like all other Injen products, the Injen exhaust systems are proudly built in Pomona, CA.

• If you're looking to improve sound, power, and looks then this is the system for you!
• Hand Crafted and TIG Welded to Perfection for Strength and Durability
• Stainless Steel Investment Cast Flanges For a Fast and Easy Install
• Full 60MM piping made from premium 304 SS Mandrel-Bent Tubing
• Dyno Proven gains of up to 8 hp and 7 lb-ft. of torque
• Features Injen's classic round JDM style rear muffler
• Embossed Injen Muffler - Excludes AWC Models
• Premium Stainless Steel Hardware and Hangers
• Manufactured in Pomona, California USA
• Beautiful 4.5"polished exhaust tip
• No Cutting or Welding Required
• Axle Back Exhaust System

This Part Fits:

The Injen Technology engineers are experts when it comes to performance, PERIOD. From Cars to Trucks to Powersports, Injen has a variety of exhaust systems to choose from. All of Injen Technology Performance exhaust systems are constructed from mandrel bent stainless steel tubing Mandrel-bending ensures the tubing maintains its shapes and size throughout the entire length, providing smooth, unrestricted airflow. From the Investment cast flanges to the custom hangers, all Injen exhaust systems are 100% TIG welded and handcrafted in the USA and include all tubing, mufflers, and hardware necessary for a hassle free installation. Each system is uniquely designed to offer an aggressive sound that brings out some massive power. Like all other Injen products, the Injen exhaust systems are proudly built in Pomona, CA.

• If you're looking to improve sound, power, and looks then this is the system for you!
• Hand Crafted and TIG Welded to Perfection for Strength and Durability
• Stainless Steel Investment Cast Flanges For a Fast and Easy Install
• Retains Original Sensors So You Wont Get A Check Engine Light
• Full 60MM piping made from premium 304 SS Mandrel-Bent Tubing
• Dyno Proven gains of up to 7 hp and 6 lb-ft. of torque
• Features Injen's classic round JDM style rear muffler
• Premium Stainless Steel Hardware and Hangers
• Beautiful 4.5"burnt titanium exhaust tip
• Manufactured in Pomona, California USA
• No Cutting or Welding Required
• Axle Back Exhaust System

This Part Fits:

So you have that new 2016-2021 Honda Civic Sedan with the 1.5L Turbo and now you crave that extra punch in sound and performance. Well, the team at Injen Technology has you covered. This aggressively designed cat-back exhaust system features a large 76mm 304 stainless steel front section that Y's into dual 60mm rear pipes that are each capped with 3.50"burnt titanium exhaust tips. This beautiful cat-back exhaust system is designed specifically for the Honda Civic Sedan to deliver improved performance that you can hear and feel. It doesn't matter if you're hitting the track or commuting to work, this dual exhaust system by Injen Technology will give you the power you need to tackle anything thrown at you. This dual titanium tip exhaust system for your Honda Civic Sedan 1.5L is constructed from mandrel bent 304 stainless steel tubing designed for a lifetime of use. By using Mandrel-bent tubing, Injen Technology ensures the tubing maintains its shape and size throughout the entire length, providing smooth, unrestricted airflow. To go the extra step, the team at Injen Technology TIG welded this system by hand for a beautiful system that is hassle free to install. If you're looking to improve sound, increased performance, and looks that turn heads, then this is the system for you!

• If you're looking to improve sound, power, and looks then this is the system for you!
• Beautiful 3.50"Dual Burnt Titanium exhaust tips for that classic JDM look
• Hand Crafted and TIG Welded to Perfection for Strength and Durability
• Stainless Steel Investment Cast Flange for a Fast and Easy Install
• Single resonator, no muffler design for a distinct exhaust note
• 76mm front section with dual 60mm rear cat-back exhaust system
• Stainless Steel Hardware and Hangers for a simple install
• Dyno Proven gains of up to 8 hp and 7 lb-ft. of torque
• Premium 304 SS Mandrel-Bent Tubing used throughout
• 76mm Stainless Steel Full Cat-Back System
• Does not fit Coupe and Hatchback models
• Designed and Made in Pomona, CA
• No Cutting or Welding Required

This Part Fits: