The Snow Performance Stage 3 Boost Cooler® brings true 2D mapped water-methanol injection delivery to your EFI (electronic fuel injected) and forced induction (turbocharged/supercharged) vehicle. The Stage 3 creates a 2D injection map based off boost and fuel injector pulse width to deliver a extremely accurate amount of water-methanol when the engine needs it most. Bringing fuel injector pulse width into the mix allows the injection curve to be extended past specific boost points for greater range/control. None invasive, the Stage 3 Boost Cooler® controller is designed to mount on the steering column or the dash so no additional gauge pods need to be purchased and functions as a boost gauge, water-meth controller and fuel system monitor all in one! Proven to reduce the air inlet temperature by up to 100 degrees and increase octane by 25 points for maximum HP and cooling . Comes with adjustable Stage 3 water-meth controller, 4AN fittings, and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.

• Cleans all carbon build up out of your motor
• Reduce air intake temps out too 100 degrees
• Two-dimensional injection map
• Increase octane by 25 points
• Built in boost gauge
• New nozzle design
• Lower EGTS

The Snow Performance Stage 3 Boost Cooler® brings true 2D mapped water-methanol injection delivery to your EFI (electronic fuel injected) and forced induction (turbocharged/supercharged) vehicle. The Stage 3 creates a 2D injection map based off boost and fuel injector pulse width to deliver a extremely accurate amount of water-methanol when the engine needs it most. Bringing fuel injector pulse width into the mix allows the injection curve to be extended past specific boost points for greater range/control. None invasive, the Stage 3 Boost Cooler® controller is designed to mount on the steering column or the dash so no additional gauge pods need to be purchased and functions as a boost gauge, water-meth controller and fuel system monitor all in one! Proven to reduce the air inlet temperature by up to 100 degrees and increase octane by 25 points for maximum HP and cooling . Comes with adjustable Stage 3 water-meth controller, 1/4" High Temp Nylon line and easy to install quick-connect fittings.

• Cleans all carbon build up out of your motor
• Reduce air intake temps out too 100 degrees
• Two-dimensional injection map
• Increase octane by 25 points
• Built in boost gauge
• New nozzle design
• Lower EGTS

Decrease EGTs and increase HP in your diesel by 65HP+ in the most cost effective water-methanol injection kit on the market! Utilizing a adjustable boost pressure switch and dual nozzles to deliver precise amounts of water-methanol once 30 boost PSI has been reached (Boost Engagement Adjustable, 30 PSI Boost Hobbs Switch Included). Recommended for all high boost and competition diesels looking to increase HP while decreasing EGTs when on heavy throttle. Comes with easy to mount race ready 3QT tank, high flow check valve, quick-connect fittings, 300 PSI UHO Pump, and LED alert system.

• Up to 65 HP Increase!

Snow Performance has combined performance, quality, and easy installation in this new water-methanol injection system engineered specifically for all forced induction (supercharged/turbocharged) Dodge Challengers/Chargers with the 5.7 / 6.1 / 6.4 engine . Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! Complete with custom water-methanol injection throttle body spacer plate, braided stainless line, and 4AN fittings offering un surpassed reliability and ease of install. The Stage 2 uses a progressive VC-50 controller (ISO 9001 Manufactured) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. The VC-50 controller (52mm gauge) offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to match your OEM gauges or mix and match up to two colors. Fits all forced induction (supercharged/turbocharged) Dodge Challenger/Chargers with 5.7 / 6.1 / 6.4 engine.

• Achieve 116 Octane Quality Fuel From Pump Gas
• Cleans Engine Combustion Of Carbon Build Up
• Progressive Water-Methanol Injection
• Safely Run More Boost & Timing
• Cooler Denser Air Charge
• Made In USA

This Part Fits:

Snow Performance has combined performance, quality and easy installation in this new water-methanol injection system engineered specifically for 2010+ Ford F-150s equipped with the 3.5L EcoBoost engine. Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! Complete with custom water-methanol injection throttle body spacer plate, braided stainless line, and 4AN fittings offering un surpassed reliability and ease of install. The Stage 2 uses a progressive VC-50 controller (ISO 9001 Manufactured) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. The VC-50 controller (52mm gauge) offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to match your OEM gauges or mix and match up to two colors. Fits all 2010+ Ford F-150s equipped with the 3.5L EcoBoost engine.

• Achieve 116 Octane Quality Fuel From Pump Gas
• Cleans Engine Combustion Of Carbon Build Up
• Progressive Water-Methanol Injection
• Safely Run More Boost & Timing
• Cooler Denser Air Charge
• Made In USA

This Part Fits:

Snow Performance has combined performance, quality and easy installation in this new water-methanol injection system engineered specifically for forced induction (supercharged/turbocharged) 2011+ Ford 5.0 Coyote engines. Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! Complete with custom water-methanol injection throttle body spacer plate, braided stainless line, and 4AN fittings offering un surpassed reliability and ease of install. The Stage 2 uses a progressive VC-50 controller (ISO 9001 Manufactured) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. The VC-50 controller (52mm gauge) offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to match your OEM gauges or mix and match up to two colors. Fits all forced induction (supercharged/turbocharged) 2011+ Ford Mustang GTs equipped with the 5.0L Coyote engine.

• Achieve 116 Octane Quality Fuel From Pump Gas
• Cleans Engine Combustion Of Carbon Build Up
• Progressive Water-Methanol Injection
• Safely Run More Boost & Timing
• Cooler Denser Air Charge
• Made In USA

This Part Fits:

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler® water-methanol injection system is available for all forced induction applications (supercharged/turbocharged). The Stage 2 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability.The Stage 2 introduces the VC-50 Controller (ISO 9001 Manufactured). The VC-50 offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to your OEM gauges or mix and match up to two colors. Comes with 4AN fittings and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.

• Snow Performance OEM-Approved Extreme Environment 300 PSI UHO Water Methanol Pump
• 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
• Recommended For Street Driven Turbo and Centrifugal Supercharger Applications
• Snow Performance Running "S" Engraved Low Profile High Flow Check Valve
• Snow Performance Running "S" Engraved Low Profile Nozzle Holder
• Adjustable Progressive Water Methanol Engagement & Monitoring
• Snow Performance ACU-SEAL Water Methanol Compression Fittings
• Snow Performance Hyper-Sonic Water Methanol Nozzle
• Digital Boost Reading (1-50 PSI)
• Supports 1,000+ HP
• U.S.A. Made

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler® water-methanol injection system is available for all forced induction applications (supercharged/turbocharged). The Stage 2 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability.The Stage 2 introduces the VC-50 Controller (ISO 9001 Manufactured). The VC-50 offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to your OEM gauges or mix and match up to two colors. Comes with 4AN fittings and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.

• Snow Performance OEM-Approved Extreme Environment 300 PSI UHO Water Methanol Pump
• 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
• Recommended For Street Driven Turbo and Centrifugal Supercharger Applications
• Snow Performance Running "S" Engraved Low Profile High Flow Check Valve
• Snow Performance Running "S" Engraved Low Profile Nozzle Holder
• Adjustable Progressive Water Methanol Engagement & Monitoring
• Snow Performance ACU-SEAL Water Methanol Compression Fittings
• Snow Performance Hyper-Sonic Water Methanol Nozzle
• Digital Boost Reading (1-50 PSI)
• Supports 1,000+ HP
• U.S.A. Made

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler® water-methanol injection system is available for all forced induction applications (supercharged/turbocharged). The Stage 2 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability.The Stage 2 introduces the VC-50 Controller (ISO 9001 Manufactured). The VC-50 offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to your OEM gauges or mix and match up to two colors. Comes with 4AN fittings and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.

• Snow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol Pump
• 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
• Recommended For Street Driven Turbo and Centrifugal Supercharger Applications
• Snow Performance Running "S" Engraved Low Profile High Flow Check Valve
• Snow Performance Running "S" Engraved Low Profile Nozzle Holder
• Adjustable Progressive Water Methanol Engagement & Monitoring
• Snow Performance ACU-SEAL Water Methanol Compression Fittings
• Snow Performance Hyper-Sonic Water Methanol Nozzle
• Digital Boost Reading (1-50 PSI)
• Supports 1,000+ HP
• U.S.A. Made

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler® water-methanol injection system is available for all forced induction applications (supercharged/turbocharged). The Stage 2 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability.The Stage 2 introduces the VC-50 Controller (ISO 9001 Manufactured). The VC-50 offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to your OEM gauges or mix and match up to two colors. Comes with 4AN fittings and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.

• Snow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol Pump
• 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
• Recommended For Street Driven Turbo and Centrifugal Supercharger Applications
• Snow Performance Running "S" Engraved Low Profile High Flow Check Valve
• Snow Performance Running "S" Engraved Low Profile Nozzle Holder
• Adjustable Progressive Water Methanol Engagement & Monitoring
• Snow Performance ACU-SEAL Water Methanol Compression Fittings
• Snow Performance Hyper-Sonic Water Methanol Nozzle
• Digital Boost Reading (1-50 PSI)
• Supports 1,000+ HP
• U.S.A. Made

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler® water-methanol injection system is available for all forced induction applications (supercharged/turbocharged). The Stage 2 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability.The VC-50 (ISO 9001 Manufactured) controller offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to your OEM gauges or mix and match up to two colors.. Comes with easy to install quick-connect fittings and 1/4" high temp nylon tubing.

• Snow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol Pump
• 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
• Recommended For Street Driven Turbo and Centrifugal Supercharger Applications
• Snow Performance Running "S" Engraved Low Profile High Flow Check Valve
• Snow Performance Running "S" Engraved Low Profile Nozzle Holder
• Adjustable Progressive Water Methanol Engagement & Monitoring
• Snow Performance ACU-SEAL Water Methanol Compression Fittings
• Snow Performance Hyper-Sonic Water Methanol Nozzle
• Digital Boost Reading (1-50 PSI)
• Supports 1,000+ HP
• U.S.A. Made

Race gas quality fuel on pump gas! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 1 Boost Cooler® water-methanol injection kit is available for all forced induction applications (supercharged/turbocharged) and uses a adjustable boost switch to inject a fixed amount of water-methanol into the system until boost goes below the switch set point. Proven to deliver 30-70 HP increases to all forced induction applications! This makes it a good choice for low to medium boost setups (1-15 PSI) and vehicles with a positive displacement supercharger looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user-chosen switch, such as a full throttle switch, nitrous switch, etc. Comes with 4AN fittings and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.

• Snow Performance OEM-Approved Extreme Environment 300 PSI UHO Water Methanol Pump
• 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
• Recommended For Street Driven Turbo and Centrifugal Supercharger Applications
• Snow Performance Running "S" Engraved Low Profile High Flow Check Valve
• Snow Performance Running "S" Engraved Low Profile Nozzle Holder
• Adjustable Progressive Water-Methanol Engagement & Monitoring
• Snow Performance ACU-SEAL Water-Methanol Compression Fittings
• Snow Performance Hyper-Sonic Water Methanol Nozzle
• Supports 1,000+ HP
• U.S.A. Made

Race gas quality fuel on pump gas! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 1 Boost Cooler® water-methanol injection kit is available for all forced induction applications (supercharged/turbocharged) and uses a adjustable boost switch to inject a fixed amount of water-methanol into the system until boost goes below the switch set point. Proven to deliver 30-70 HP increases to all forced induction applications! This makes it a good choice for low to medium boost setups (1-15 PSI) and vehicles with a positive displacement supercharger looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user-chosen switch, such as a full throttle switch, nitrous switch, etc. Comes with easy to install quick-connect fittings and 1/4" high temp nylon tubing.

• Snow Performance OEM-Approved Extreme Environment 300 PSI UHO Water Methanol Pump
• 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
• Recommended For Street Driven Turbo and Centrifugal Supercharger Applications
• Snow Performance Running "S" Engraved Low Profile High Flow Check Valve
• Snow Performance Running "S" Engraved Low Profile Nozzle Holder
• Adjustable Progressive Water-Methanol Engagement & Monitoring
• Snow Performance ACU-SEAL Water-Methanol Compression Fittings
• Snow Performance Hyper-Sonic Water Methanol Nozzle
• Supports 1,000+ HP
• U.S.A. Made

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler® water-methanol injection kit is available for all forced induction applications (supercharged/turbocharged) and uses a progressive controller with built in manifold absolute pressure (MAP) sensor that proportionally injects more or less water-methanol according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. Comes with adjustable progressive VC-20 engine mount controller, 4AN fittings, and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.

• Snow Performance OEM-Approved Extreme Environment 300 PSI UHO Water Methanol Pump
• 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
• Recommended For Street Driven Turbo and Centrifugal Supercharger Applications
• Snow Performance Running "S" Engraved Low Profile High Flow Check Valve
• Snow Performance Running "S" Engraved Low Profile Nozzle Holder
• Adjustable Progressive Water-Methanol Engagement & Monitoring
• Snow Performance ACU-SEAL Water-Methanol Compression Fittings
• Snow Performance Hyper-Sonic Water Methanol Nozzle
• Supports 1,000+ HP
• U.S.A. Made

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler® water-methanol injection kit is available for all forced induction applications (supercharged/turbocharged) and uses a progressive controller with built in manifold absolute pressure (MAP) sensor that proportionally injects more or less water-methanol according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. Comes with adjustable progressive VC-20 engine mount controller, 4AN fittings, and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.

• Snow Performance OEM-Approved Extreme Environment 300 PSI UHO Water Methanol Pump
• 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
• Recommended For Street Driven Turbo and Centrifugal Supercharger Applications
• Snow Performance Running "S" Engraved Low Profile High Flow Check Valve
• Snow Performance Running "S" Engraved Low Profile Nozzle Holder
• Adjustable Progressive Water-Methanol Engagement & Monitoring
• Snow Performance ACU-SEAL Water-Methanol Compression Fittings
• Snow Performance Hyper-Sonic Water Methanol Nozzle
• Supports 1,000+ HP
• U.S.A. Made

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler® water-methanol injection kit is available for all forced induction applications (supercharged/turbocharged) and uses a progressive controller with built in manifold absolute pressure (MAP) sensor that proportionally injects more or less water-methanol according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. Recommended for all gas forced induction vehicles using a turbo or centrifugal supercharger. Comes with adjustable progressive VC-20 engine mount controller and easy to install quick-connect fittings.

• Snow Performance OEM-Approved Extreme Environment 300 PSI UHO Water Methanol Pump
• 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
• Recommended For Street Driven Turbo and Centrifugal Supercharger Applications
• Snow Performance Running "S" Engraved Low Profile High Flow Check Valve
• Snow Performance Running "S" Engraved Low Profile Nozzle Holder
• Adjustable Progressive Water-Methanol Engagement & Monitoring
• Snow Performance ACU-SEAL Water-Methanol Compression Fittings
• Snow Performance Hyper-Sonic Water Methanol Nozzle
• Supports 1,000+ HP
• U.S.A. Made

The first of its kind, Skunk2's Black Series Billet VTEC Solenoid is designed to be used with Hondas F20C1 and F22C1 cylinder heads and is compatible with Honda's original pressure sensor, solenoid internals, and gasket. Billet VTEC Solenoids for Hondas F-series engines are available exclusively in Skunk2s Black Series finish. Manufactured from 6061-T6 billet aluminum and hard anodized for durability, Skunk2 employs the same design and manufacturing methods for all of its Fine Tuning accessories as it does for its top-of-the-line racing components. Each Billet VTEC Solenoid includes flush-mounted hardware and a smooth, machined body for an attractive look. Skunk2's Billet VTEC Solenoids help put that unique finishing touch onto the vehicle you work so hard to make perform well, and we make every effort to ensure that their style is consistent with our rich racing heritage.

• Manufactured From 6061 Billet Aluminum
• Black Anodized Finish
• US Patent No. D676393

This Part Fits:

The first of its kind, Skunk2's Black Series Billet VTEC Solenoid is designed to be used with any H22A cylinder head and is compatible with Honda's original pressure sensor, solenoid internals, and gasket. Billet VTEC Solenoids for Hondas H-series VTEC engines are available exclusively in Skunk2s Black Series finish. Manufactured from 6061 billet aluminum and hard anodized for durability, Skunk2 employs the same design and manufacturing methods for all of its Fine Tuning accessories as it does for its top-of-the-line racing components. Each Billet VTEC Solenoid includes flush-mounted hardware and a smooth, machined body for an attractive look. Skunk2's Billet VTEC Solenoids help put that unique finishing touch onto the vehicle you work so hard to make perform well, and we make every effort to ensure that their style is consistent with our rich racing heritage.

• Manufactured From 6061 Billet Aluminum
• Black Anodized Finish
• US Patent No. D684937

This Part Fits:

The first of its kind, Skunk2's Hard Anodized Billet VTEC Solenoid is designed to be used with any B16A/B or B18C cylinder head and is compatible with Honda's original pressure sensor, solenoid internals, and gasket. Billet VTEC Solenoids for Hondas B-series VTEC engines are available exclusively in Skunk2s Hard Anodized finish. Manufactured from 6061 billet aluminum and hard anodized for durability, Skunk2 employs the same design and manufacturing methods for all of its Fine Tuning accessories as it does for its top-of-the-line racing components. Each Billet VTEC Solenoid includes flush-mounted hardware and a smooth, machined body for an attractive look. Skunk2's Billet VTEC Solenoids help put that unique finishing touch onto the vehicle you work so hard to make perform well, and we make every effort to ensure that their style is consistent with our rich racing heritage.

• Manufactured From 6061 Billet Aluminum
• US Patent No. D658593
• Hard Anodized Finish

This Part Fits:

Skunk2 is proud to introduce its all-new FA20 BRZ/FRS Oil Cooler Kit. The kit includes a sandwich adapter which is made from 6061 Aluminum, CNC machined and then hard-anodized. Skunk2s Oil Filter Sandwich Adapter features a 1/8 pipe port to feed a turbo or the addition of a pressure gauge. The Skunk2 FA20 BRZ/FRS Oil Cooler Kit fits the Kraftwerks supercharger kit and has been ran and tested on Kraftwerks very own FA20. The Oil Cooler features 19 rows of fins and sits towards the front of the bay where most cooler and filtered air is located. The positioning of the Cooler allows for cooler air which then results in cooler temperatures. The cooler it self measures at 11.25 in.x5.5 in. with -10 outlets and is 2 in. thick. With all these features combined the Skunk2 Oil Cooler Kit stands apart in performance and quality as well sleek appearance in comparison to any other cooler out in the market. This Bolt-On Solution is compatible with the Kraftwerks Supercharger Kit for the FRS/BRZ and includes everything you need to install. No Cutting, Welding or Drilling Required.

• Hard Anodized In Black For Durability And Good Looks
• Dimensions 330mm x 163mm x 50.8mm
• 6062 Aluminum Construction
• Large -10 Inlet/Outlets
• Incl. Mounting Hardware
• 20 Row Core

This Part Fits:

This Part Fits:

This Part Fits:

This Part Fits:

This Part Fits:

This Part Fits:

This Part Fits:

This Part Fits: