In-Line Fuel Filter, Standard Length, -6AN Inlet/Outlet, 10 micron replaceable fabric element

In-Line Fuel Filter, Standard Length, -6AN Inlet/Outlet, 10 micron replaceable fabric element

6 micron micro-fiberglass replacement element, 5 inch, with 2 o-rings and instructions

10 micron paper replacement element, 5 inch, with 2 o-rings and instructions

6 micron micro-fiberglass replacement element, 3 inch, with 2 o-rings and instructions

75 micron stainless steel replacement element, 3 inch, with 2 o-rings and instructions

40 micron stainless steel replacement element, 3 inch, with 2 o-rings and instructions

10 micron paper replacement element, 3 inch, with 2 o-rings and instructions

Easily rebuild your lift pump and stage 1 fuel filter assembly on your Cummins equipped 2016-2019 Nissan Titan XD with our complete rebuild kit! Our Fleece Performance Lift Pump and Filter Kit includes a brand new fuel pump, Fleet Guard fuel filters, and all necessary O-rings to update your fuel filter housing and fuel pump assembly. Kit includes: New OE replacement fuel pump New Fleet Guard stage 1 lower filter New Fleet Guard under hood filter New O-rings for the fuel pump / stage 1 filter head Application Notes For use in 2016-2019 Nissan Titan XD trucks equipped with the 5.0L Cummins that utilize fuel filter and fuel pump assembly 16400-EZ40B or 16400-EZ40A Installer Notes The fuel pump priming procedure outlined in the installation instructions must be performed after the fuel pump and filter replacement are complete and prior to first engine cranking. This process ensures that all air is cleared from the fuel system, allowing the pump to build adequate fuel pressure. Failure to follow this procedure will result in low fuel feed pressure, a long start" engine, and pump damage.

This Part Fits:

The Fleece Performance L5P fuel filter upgrade kit allows you to seamlessly change over from the stock cartridge style filter to a spin-on canister style filter. The canister filter provides for increased filter capacity and longer change intervals as well as expands your filter options. Our anodized billet aluminum fuel filter base retains the OE sandwich style heating element and includes quick disconnect fittings for an OE quality fit and finish. The new filter base installs in the same location as the stock cartridge filter base. Kit includes: Donaldson fuel filter and water separator Filter base with integral mounting Distribution filter block / filter coupler Quick disconnect fittings Fitment: 2017–2019 L5P Duramax (Short and Long Bed) 2020-2024 L5P Duramax Long Bed Cross-Reference: Replaces GM Part # 23149526, 84711317, 84996837 US PATENT. NO. D978,917

This Part Fits:

All New Fleece Performance replacement under hood filter assembly for the Ford F250/350/450 6.7L Powerstroke! The plastic OE filters are prone to cracking and fuel leakage - eliminate the risk of a cracked filter with our billet aluminum cap assembly and billet aluminum quick disconnect fittings. Our drop-in replacement filter assembly locks directly into the stock filter location and utilizes a replaceable spin-on Donaldson filter that is easily serviceable. The kit includes an extra Donaldson fuel filter, further extending the time before you need to purchase an additional filter. Features Drop-in replacement for the factory underhood filter Heavy duty anodized billet aluminum cap Heavy duty anodized billet aluminum quick-disconnect fittings Steel adapter fitting for the filter Extra Donaldson P555095 filter included with the kit Application Notes Fits 2011-2026 F250/350/450 with 6.7L Powerstroke. The 2011-2016 model trucks use only one inlet and one outlet fitting. For 2017-2026 trucks, an additional quick disconnect fitting is provided for the required additional fuel return. This product fits 2011-2024 trucks equipped with an S&S DCR Conversion kit or the S&S Disaster Prevention Kit. Kit includes the following Fleece Performance components: FPE-34552-A, FPE-34550-A, FPE-34781-A, FPE-FF-M16-ADPT, FPE-SP-3416.

• Heavy duty anodized billet aluminum quick-disconnect fittings
• Drop-in replacement for the factory underhood filter
• Heavy duty anodized billet aluminum cap
• Steel adapter fitting for the filter

This Part Fits:

The Fleece Performance under bed filter for the 2011-2016 6.7L Power Stroke allows you to maintain both your under bed and under hood fuel filters separately instead of being required to purchase in a kit. Combine our improved performance filter with our engine mounted filter assembly (FPE-FMC-UHFA-1123) for the most reliable drop-in filtration on the market. The Fleece Performance filter features a higher efficiency of particulate removal across the entire filter range, ensuring greater particulate removal at higher flow rates. Application Notes Fits 2011-2016 F250/350/450/550 with 6.7L Power Stroke. Replaces the under bed filter in Motorcraft kit FD-4615.

This Part Fits:

The Donaldson P555095 Fuel Filter is a direct replacement filter for use with the Fleece Performance Engine Mounted Filter Assembly for 6.7L Ford Powerstroke, part number FPE-FMC-UHFA-1123. Fits the following kits:FPE-FMC-UHFA-1123

Introducing our all-new full featured auxiliary fuel filter kit for the 2011-2016 LML 6.6L Duramax! This kit replaces the factory fuel filter housing with a new filter base, integral high-flow fuel heater, Water-In-Fuel (WIF) sensor, and Donaldson spin-on canister style filter. The filter base eliminates the factory fuel primer bulb and is intended for use with a positive pressure lift pump such as our PowerFlo lift pump or alternative frame mounted pump. Problem: The LML Duramax was not originally equipped with a fuel heater, making it prone to fuel gelling in cold temperatures. Solution: Our updated fuel filter base mounts in the factory location, providing for a direct factory replacement and the peace of mind to tackle the coldest of days with a high-flow fuel heater. Kit includes: Fuel filter base with integral fuel heater and fittings Donaldson 3 micron fuel filter and water separator Pre-formed hose and hose clamps Wiring harness and fuse taps Water-In-Fuel (WIF) sensor and adaptation harness Fuel heater specifications: Temperature switching points: ON: 28.4F +/-5.4F, OFF: 48.2F +/- 5.4F At typical fuel flow rates a temperature increase of between 4-8F will occur across the heating element Application Notes: For 2011-2016 6.6L Duramax only This filter base eliminates the factory fuel primer bulb and is intended ONLY for use with a positive pressure lift pump such as our PowerFlo lift pump or alternative frame mounted pump.

• Fuel filter base with integral fuel heater and fittings
• Donaldson 3 micron fuel filter and water separator
• Water-In-Fuel (WIF) sensor and adaptation harness
• Pre-formed hose and hose clamps
• Wiring harness and fuse taps

This Part Fits:

Tired of over-priced fuel filter service costs and questionable filter options? Our direct replacement under bed fuel filter base for the 2019-2024 Ram with 6.7L Cummins allows you to convert to a more convenient Donaldson spin-on filter and will lower your ongoing filter maintenance costs. This kit replaces the factory plastic fuel filter housing with a new anodized billet aluminum filter base, Donaldson spin-on canister style filter, Water-In-Fuel (WIF) sensor, and integral high-flow fuel heater option. No additional lines to route, cut, or install with the option to add a full-flow fuel heater - our kit easily mounts in the factory location and connects directly to all factory fuel lines and WIF sensor circuitry. Fully assembled filter base is ready to install! Kit includes: Anodized aluminum fuel filter base with quick connect fittings Donaldson P551329 fuel filter and water separator Water-In-Fuel (WIF) sensor and adapter harness Mounting bolts Option to add a high-flow fuel heater This kit is a direct replacement for MOPAR 68358393AA filter assembly that utilizes MOPAR filter 68436631AA

This Part Fits:

Auxiliary fuel filter and line kit for your 2003-2018 Dodge Cummins. The kit includes everything you need to properly route, plumb and filter fuel for your Cummins engine from the lift pump to the injection pump. Our kit improves accessibility to the fuel filter as well as reduces your ongoing maintenance cost with a the lower cost Donaldson filter. A Fleece Performance fuel filter delete kit is required for use with this product. Kit includes: Donaldson 3 micron fuel filter and water separator (Donaldson P/N P553207) Filter base with integral mounting Distribution filter block / filter coupler Push Lock hose and all necessary AN and barb fittings CP3 Feed fittings for 5.9L and 6.7L

This Part Fits:

Fuel pump module filter element, stainless steel 10 micron, for 1993-2005 Subaru Impreza

This Part Fits:

Stainless steel 10 micron fuel filter, for 2005-2010 Mustang

This Part Fits:

Universal Spin-on Filter Kit with disposable spin-on fuel filter element, 5 micron. E85 compatible. Universal

In-line fuel filter element and housing kit, stainless steel 10 micron, -8AN, 160mm. Universal

In-line fuel filter element and housing kit, stainless steel 10 micron, 10AN, 160mm. Universal

DeatschWerks, LLC provides high-performance fuel system solutions for the automotive aftermarket. Located in Oklahoma City, OK, DW houses all of the company?s functions including design, end-manufacturing, quality assurance, sales, marketing, and administration in its 36,000sf facility. DeatschWerks? roots were established in 2004 by offering high flow drop-in fitment fuel injectors. In 2009 DW expanded into fuel pumps with the DW300, the highest flowing in-tank fuel pump of its time. Since then, DW has developed a wide range of innovative fuel system components which include in-tank and in-line pumps, surge tanks, fuel rails, fuel filters, pressure regulators, and a fuel-specific lines, fittings, and adaptors. Today, the DeatschWerks line-up of fuel system components includes over 800 SKU?s covering Sport Compact, Modern Muscle, Euro, and Powersport applications.

In-line fuel filter element and housing kit, stainless steel 100 micron, -8AN, 110mm. Universal