Fits select 2018-2023 Jeep Wrangler, Gladiator, and 2019-2023 Ford Bronco and Ranger models equipped with the M220 rear axle.

Restore drivetrain efficiency and eliminate wheel-end vibrations with the Yukon Gear & Axle AK R-J01 Rear Axle Shaft Bearing and Seal Kit. Specifically engineered for the Dana M220 (AdvanTEK) rear axle found in modern off-road platforms, this kit provides the precise fitment and structural integrity required for heavy-duty use and oversized tire applications.

• Precision Engineering: Designed to meet or exceed OE specifications for the M220 rear axle, ensuring a seamless installation without modifications.
• Durable Contaminant Protection: High-quality seals safeguard axle shafts against dirt, moisture, and trail debris to prevent premature bearing failure.
• Smooth Operation: Reduces drivetrain friction and noise by providing optimal support for the rear axle shafts.
• Complete Solution: Includes the necessary bearing and seal to service one side of the vehicle.
• Part Number: AK R-J01

Fits 1976-1986 Jeep CJ5, CJ7, and Scrambler with AMC Model 20 rear axles using a 1-piece axle design.

Yukon Gear & Axle bearing and seal kits are engineered to restore smooth, quiet operation and reliable fluid retention at the wheel ends. This specific kit (AK M20-1PIECE) is designed for AMC Model 20 rear differentials that have been upgraded or converted to a 1-piece axle shaft design, a common modification to improve strength over the factory two-piece setup.

Each kit contains high-quality components designed for precision fitment and durability under off-road and street conditions. This kit services one side of the vehicle; two kits are required for a complete rear axle service.

• Specifically for 1-piece axle shaft designs
• Includes (1) high-quality axle bearing
• Includes (1) inner axle seal
• Includes (1) outer axle seal
• Services one side of the rear axle
• Manufacturer Part Number: AK M20-1PIECE

Fits select 1972-2013 Chevrolet and GMC C20, K20, C30, K30, 2500, and 3500 series trucks, vans, and SUVs with the 10.5-inch 14-bolt rear axle.

The Yukon Gear AK GM14T Axle Bearing and Seal Kit is a precision-engineered solution for servicing the hub assembly on the heavy-duty GM 10.5" 14-bolt full-floating rear end. This kit provides the critical components needed to restore smooth rotation and eliminate the noise or heat associated with worn-out wheel bearings. By replacing pitted races and tired seals, you ensure proper lubricant retention and protect your axle shafts from premature wear.

This kit services one side of the vehicle; two kits are required for a complete rear axle overhaul. Every component is selected to meet or exceed original equipment specifications for fitment and durability in high-torque towing and off-road environments.

• MPN: AK GM14T
• Application: GM 10.5" 14-Bolt Full-Float Rear Axle
• Includes: Inner and outer bearings, matching races, and axle seal
• Service: Completes one side/wheel hub
• Compatibility: Direct replacement for OE bearing and seal sets

Fits 2007-2018 Jeep Wrangler and Wrangler JK (all submodels including Rubicon, Sahara, Sport, and X).

Restore the reliability and smooth operation of your rear drivetrain with the Yukon Gear Replacement Axle Bearing and Seal Kit. Specifically engineered for the Jeep JK chassis, this kit addresses the common wear points in the rear axle assembly. By replacing worn factory bearings and seals with Yukon’s high-quality components, you eliminate excessive axle shaft play and prevent gear oil leaks that can lead to premature differential failure.

• Direct replacement for factory rear axle bearings and seals
• Designed to service one side of the vehicle
• High-quality materials for extended service life in demanding off-road conditions
• Precision tolerances for proper axle shaft alignment and heat dissipation
• Manufacturer Part Number: AK D44JK

Each kit includes one axle bearing and one axle seal, providing the necessary hardware for a complete service on either the driver or passenger side of the rear axle housing.

Fits select 1961-1974 Chrysler, Dodge, and Plymouth models equipped with the 8.75-inch rear axle. This comprehensive Yukon Gear kit is engineered to service both the driver and passenger sides, providing a complete solution for restoring axle integrity and preventing fluid leaks.

The kit includes high-quality replacement bearings and precision seals designed to handle the loads of classic Mopar drivetrains. By including the threaded adjusters and retaining plates, this set allows for precise bearing preload settings during installation, ensuring long-term durability for your rear-end assembly.

• Fits 8.75-inch Chrysler axle applications
• Complete kit services both the left and right sides
• Includes axle bearings, inner seals, and outer seals
• Features retaining plates, adjusters, and adjuster plates
• Manufacturer Part Number: AK C8.75-OEM-COMPLETE

Fits select 1988-2016 Cadillac Escalade, Chevrolet Silverado, Tahoe, S10, and GMC Sierra, Yukon, and Savana models.

The Yukon Gear Axle Bearing and Seal Kit (AK C10) is a precision-engineered solution for restoring the drivetrain integrity of your GM truck or SUV. This kit provides the necessary high-quality components to replace a worn factory wheel bearing and a leaking seal on one side of the vehicle. By addressing these components simultaneously, you prevent fluid loss and eliminate the metal-on-metal friction that can lead to catastrophic axle shaft or housing wear.

• Manufacturer Part Number: AK C10
• Outer Diameter: 2.800 inches
• Application: Services one side of the axle
• Contents: (1) Axle Bearing, (1) Axle Seal

Each kit features application-specific bearings and seals designed to meet or exceed original equipment tolerances. This ensures a proper press-fit and a reliable seal against gear oil leakage, maintaining the lubrication required for long-term axle longevity.

Fits select 2004-2019 Chrysler Aspen, Dodge Durango, Dodge Nitro, Dodge Ram 1500, Jeep Liberty, and Ram 1500.

The Yukon Gear Rear Wheel Bearing and Seal Kit (AK 6410) is a vehicle-specific solution designed to restore smooth axle rotation and maintain a leak-free seal. This kit replaces worn or noisy factory components, addressing common drivetrain issues like humming, vibration, or gear oil seepage at the wheel ends.

• Vehicle Service: Includes one axle bearing and one seal to service one side.
• Precise Tolerances: Manufactured to match original equipment dimensions for a reliable press-fit installation.
• Component Specifications:
  • Inner Diameter: 1.710 in.
  • Outer Diameter: 2.536 in.
  • Manufacturer Part Number: AK 6410

Fits select 1964-2002 Buick, Chevrolet, and Ford vehicles, including Camaro, Chevelle, El Camino, Nova, and Aerostar. This Yukon Gear & Axle bearing and seal kit (AK 1563) is engineered to restore smooth operation and prevent gear oil leaks by replacing worn rear axle components. Each kit contains high-quality Torrington bearings, recognized for their precise tolerances and durability under heavy rotational loads.

Designed to service one side of the vehicle, this kit provides a direct replacement for the factory bearing and seal. The components are manufactured to meet or exceed original equipment specifications, ensuring a proper fit within the axle housing and a reliable seal against the axle shaft surface.

• Manufacturer Part Number: AK 1563
• Bearing Brand: Torrington
• Outer Diameter: 2.250 in
• Inner Diameter: 1.400 in
• Service Limit: Services one side
• Includes: (1) Axle Bearing, (1) Axle Seal

Fits select 1980-2009 Buick, Chevrolet, Chrysler, Dodge, Ford, and GMC vehicles (5.9L).

The Yukon Gear AK 1559 Axle Bearing and Seal Kit is a high-quality replacement designed to restore smooth rotation and prevent gear oil leaks at the wheel ends. This kit features a premium Torrington bearing to ensure long-term durability and precise fitment within the axle housing. It is specifically designed to service one side of the vehicle, replacing worn components that can cause noise, vibration, or seal failure.

This kit is compatible with Ford housings using tag numbers 802, 820, 821, 824, 825, 826, 828, 829, 852, 854, 862, 869, 871, 909, and 919. Note: For tag numbers 930, 933, 935, 939, 941, and 953, please use Yukon part number AK 1561FD.

• Manufacturer Part Number: AK 1559
• Bearing Brand: Torrington
• Outer Diameter: 2.530 inches
• Inner Diameter: 1.618 inches / 1.620 inches
• Includes: (1) Axle Bearing and (1) Axle Seal
• Services one side of the axle

Fits 1997-2006 Jeep Wrangler TJ with the Dana 44 rear axle.

This Revolution Gear & Axle Rear Axle Bearing & Seal Kit (AK-TJ) provides the necessary professional-grade components to service or rebuild the axle ends on your Jeep Wrangler TJ. Designed specifically for the Dana 44 rear housing, this kit replaces worn or leaking factory components to restore proper shaft support and prevent gear oil leaks at the wheel ends, ensuring your drivetrain remains reliable on and off the trail.

• Application-specific for Dana 44 rear axles
• Replaces worn wheel bearings and outer seals to eliminate noise and leaks
• Direct fit for 1997-2006 Jeep Wrangler TJ models
• Includes high-quality components for both rear axle shafts
• Manufacturer Part Number: AK-TJ

The QA1 MCOM-T Series spherical bearing (MPN: MCOM16T) is a high-strength metric solution designed for suspension linkages and mechanical pivots. This 16mm bore bearing is engineered for durability, featuring a heat-treated chromoly steel race with a protective coating for superior corrosion resistance.

The internal ball is manufactured from precision-ground 52100 bearing steel, heat-treated and hard chrome plated to ensure smooth articulation and reduced wear under load. To maintain maintenance-free operation, the MCOM16T includes a self-lubricating PTFE liner that reduces friction and eliminates the need for external grease.

• Manufacturer Part Number: MCOM16T
• Bore Diameter: 16mm
• Ball Material: 52100 Bearing Steel (Heat Treated, Hard Chrome Plated)
• Race Material: Chromoly Steel (Heat Treated, Protective Coated)
• Liner: Self-Lubricating PTFE (MCOM-T Series)
• Construction: Precision Ground for tight tolerances

The QA1 COM-T Series spherical bearing kit (COM8T-102PK) provides a durable and cost-effective solution for suspension links, control arms, and custom fabrication where a reliable pivot point is required. This kit is designed for high-load applications and includes a snap ring for secure housing retention.

The bearing is engineered with a 52100 bearing steel ball that is heat-treated, precision ground, and hard chrome plated to ensure a smooth, wear-resistant surface. Its race is constructed from heat-treated chromoly steel with a protective coating for superior corrosion resistance. This COM-T variant features a self-lubricating PTFE liner, eliminating the need for external grease while maintaining low friction and reducing maintenance intervals.

• Manufacturer Part Number: COM8T-102PK
• Bore Diameter: .5in
• Bearing Width: 1in
• Ball Material: 52100 Bearing Steel (Heat Treated, Hard Chrome Plated)
• Race Material: Chromoly Steel (Heat Treated, Protective Coated)
• Liner: Self-Lubricating PTFE (T-Series)
• Included Hardware: Installation Snap Ring

The QA1 COM Series COM6 spherical bearing provides a durable, precision-engineered solution for suspension linkages, steering components, and custom fabrication projects. Designed for applications requiring high-strength rotation without the deflection associated with traditional rubber bushings, this metal-to-metal bearing offers consistent performance in demanding environments.

• Precision-Ground Ball: Manufactured from 52100 bearing steel, heat-treated, and hard chrome-plated for maximum wear resistance and smooth operation.
• High-Strength Race: Constructed from heat-treated chromoly steel with a protective coating to resist corrosion and ensure structural integrity under load.
• Optimized Clearances: Precision-ground tolerances provide a reliable fit for 3/8-inch bore applications.

Specifications:
Manufacturer Part Number: COM6
Bore Diameter: 3/8 inch
Ball Material: 52100 Bearing Steel (Hard Chrome Plated)
Race Material: Heat-Treated Chromoly Steel

The QA1 COM12T COM-T Series spherical bearing is engineered for high-load automotive applications where precision articulation is required. This 3/4-inch bore bearing features a race constructed from heat-treated chromoly steel, coated for superior corrosion resistance. The internal ball is manufactured from precision-ground 52100 bearing steel that has been heat-treated and hard chrome plated for a durable, hard-wearing surface.

Equipped with a self-lubricating PTFE liner, the COM12T eliminates the maintenance requirements of traditional greaseable bearings while providing a low-friction interface. These bearings are ideal for custom suspension builds, steering joints, and linkage points where durability and tight tolerances are paramount.

• Manufacturer Part Number: COM12T
• Bore Diameter: 3/4 inch
• Ball Material: 52100 Bearing Steel (Heat Treated, Hard Chrome Plated, Precision Ground)
• Race Material: Chromoly Steel (Heat Treated, Protective Coated for Corrosion Resistance)
• Liner: Self-Lubricating PTFE
• Series: COM-T (Traditional Spherical Bearing)

The QA1 COM10T COM-T Series spherical bearing is engineered for high-strength articulation in steering and suspension linkages. This 5/8-inch bore bearing features a precision-ground ball made from heat-treated 52100 bearing steel, which is hard chrome plated for reduced wear and increased longevity. The race is constructed from heat-treated chromoly steel and finished with a protective coating to provide superior corrosion resistance.

Designed for maintenance-free performance, the COM10T includes a self-lubricating PTFE liner that eliminates the need for constant greasing while ensuring smooth operation under load. Whether used in custom fabrications or as a replacement for worn OE joints, this spherical bearing delivers the tight tolerances required for precision automotive applications.

• Manufacturer Part Number: COM10T
• Bore Size: 5/8 inch
• Ball Material: 52100 Bearing Steel (Heat Treated, Hard Chrome Plated)
• Race Material: Chromoly Steel (Heat Treated, Corrosion Resistant Coating)
• Liner: Self-Lubricating PTFE
• Construction: Precision Ground

Fits select 1991-2004 Toyota 4Runner, Previa, T100, and Tacoma models equipped with 2.4L or 2.7L engines.

Maintain precise crankshaft axial clearance with this King Engine Bearings thrust washer set. Designed to control crankshaft end play, these thrust washers are essential for protecting your engine block and crankshaft from excessive longitudinal movement. Whether you are performing a standard rebuild or a performance overhaul on a 2RZ-FE or 3RZ-FE engine, these components provide the consistent tolerances required for long-term reliability.

• Manufacturer Part Number: TW285AM
• Engine Fitment: Toyota 2.4L (2RZ-FE) and 2.7L (3RZ-FE)
• Function: Replaces worn OE thrust washers to restore proper crankshaft end play
• Construction: High-quality materials engineered for durability and reduced friction

Fits select 1987-2005 Chrysler, Dodge, Hyundai, Mitsubishi, and Plymouth models equipped with the 6G71, 6G72, 6G72T, 6G73, or G6AV V6 engines.

This King Engine Bearings thrust washer set is engineered to maintain precise crankshaft axial clearance and control end play. Specifically designed for the 6G7-series and G6AV engine architectures, these washers provide a durable bearing surface to prevent internal engine wear and ensure proper alignment of the rotating assembly. Whether performing a standard rebuild or a performance overhaul on a forced-induction 6G72T, these components deliver the dimensional accuracy required for long-term reliability.

• Maintains critical crankshaft axial tolerances and prevents end play
• Precision manufactured for consistent material thickness and oil film retention
• Specifically designed for Mitsubishi 6G71, 6G72, 6G72T, 6G73 and Hyundai G6AV V6 engines
• High-quality construction replaces worn or damaged factory thrust washers
• Manufacturer Part Number: TW247AM

Fits select 1980-1997 Toyota Corolla, Tercel, MR2, Celica, and Geo Prizm models equipped with 1A, 2A, 3A, or 4A series engines.

This King Engine Bearings TW231AM thrust washer set is engineered to maintain precise crankshaft axial clearance, preventing excessive horizontal movement that can lead to internal engine wear or oil pressure issues. Manufactured to exact tolerances, these washers are critical for bottom-end rebuilds where maintaining proper thrust control is essential for the longevity of the engine's rotating assembly.

• Manufacturer Part Number: TW231AM
• Engine Series Compatibility: Toyota 1A, 2A, 3A, 4A
• Vehicle Application Range: 1980-1997
• Material: High-quality bearing alloy for optimal wear resistance
• Component Type: Crankshaft Thrust Washer Set