Fits 2018-2025 Jeep Wrangler JL and Gladiator JT models equipped with the factory steel bumper group.

The Artec Industries Winch Plate V3 provides a heavy-duty mounting solution for recovery winches on Jeep JL and JT platforms. Engineered to integrate seamlessly with the factory steel bumper, this winch plate is built from high-strength steel to withstand the extreme loads encountered during off-road recovery. The V3 design optimizes winch positioning for better clearance and airflow while maintaining a low-profile aesthetic that complements the OE bumper lines.

• Specifically designed for the factory steel bumper group
• Precision-engineered steel construction for maximum durability
• Bolt-on installation using factory mounting points
• Compatible with most standard recovery winches
• Maintains structural integrity during high-stress extractions
• Manufacturer Part Number: JL5611

Fits 2018-2025 Jeep Wrangler JL and Gladiator JT models.

Expand your off-road lighting capabilities with the Artec Industries Dual LED Cube Light A-Pillar Mounts. These brackets are specifically engineered to provide a secure, low-profile mounting solution for two 3-inch LED pods per side, positioning them at the base of the windshield for maximum peripheral visibility on the trail. By utilizing the factory mounting points on the lower A-pillar, these mounts ensure a rigid installation that resists vibration during high-speed washboards or technical rock crawling.

• Supports two LED cube lights per side for a total of four auxiliary lights
• Precision-engineered for 2018-2025 Jeep JL and JT platforms
• Bolts directly to factory A-pillar mounting points with no drilling or cutting required
• Low-profile design helps minimize hood glare and maintains driver line-of-sight
• Constructed for durability in harsh off-road environments
• Manufacturer Part Number: JL5603

Fits 2018-2025 Jeep Wrangler JL and Gladiator JT.

The Artec Industries Nighthawk Front Swaybar Skid is designed to provide essential armor for the vulnerable front steering and sway bar components on your Jeep. On the trail, the electronic sway bar disconnect motor and steering gear are susceptible to impact damage from rocks and debris; this skid plate offers a heavy-duty barrier to prevent costly trail failures. As part of the Nighthawk series, it is engineered for a precise fit that maintains maximum ground clearance while offering superior protection.

• Compatible with 2018-2025 Jeep Wrangler JL and Gladiator JT models
• Shields factory sway bar components and steering gear from off-road impacts
• Heavy-duty construction designed for rugged trail use
• Bolt-on installation for a secure, integrated fit
• Manufacturer Part Number: JL5304

Upgrade your 2018-2025 Jeep Wrangler JL or Gladiator JT with Artec Industries Vented Front Inner Fenders. These liners are specifically engineered to replace the flimsy factory plastic guards, providing superior protection for your engine bay against trail debris while maintaining essential airflow. Designed with a vented layout to help dissipate engine heat, this set is precision-cut to accommodate Falcon Shocks, ensuring proper clearance for reservoirs and mounting hardware.

• Fits 2018-2025 Jeep Wrangler JL and Gladiator JT (All Engines)
• Specifically designed for compatibility with Falcon Shocks
• Vented design improves airflow and engine bay cooling
• Constructed for maximum tire clearance during articulation
• Replaces restrictive factory plastic inner liners
• Manufacturer Part Number: JL5114

Fits 2018-2025 Jeep Wrangler JL and Gladiator JT models including Sahara (All Engines).

Protect your engine bay from trail debris while significantly improving thermal management with Artec Industries Front Vented Inner Fenders. These liners replace the flimsy factory plastic guards with a more durable, precision-engineered solution designed to withstand the rigors of off-roading. The integrated vented design facilitates better airflow, helping to dissipate heat build-up under the hood—a critical advantage during low-speed rock crawling or high-load situations.

• Specifically engineered for 2018-2025 Jeep Wrangler JL and Gladiator JT platforms
• Vented architecture promotes engine bay cooling and heat dissipation
• Provides superior protection for critical components against mud, rocks, and road salt
• Designed to accommodate all engine configurations
• Manufacturer Part Number: JL5113

Fits 2018-2025 Jeep Wrangler JL Sahara.

Improve your vehicle’s trail readiness and aesthetics with Artec Industries Rear Inner Fenders. These liners are engineered to replace the factory plastic components, providing a more robust barrier against mud, rocks, and debris while increasing clearance for larger tires and high-articulation suspension setups.

• Precision-engineered for the 2018-2025 Jeep Wrangler JL Sahara
• Protects rear wheel wells and chassis components from trail damage
• Enhances aesthetics with a clean, professional appearance
• Designed to accommodate oversized tires and increased suspension travel
• Manufacturer Part Number: JL5111

Reinforce your vehicle's rear end for demanding off-road use with the Artec Industries Apex Rear Axle Truss. Specifically engineered for the 2018-2025 Jeep Wrangler JL Sahara, this truss provides essential structural rigidity to the factory axle housing, preventing the axle tubes from bending or the housing from deflecting under the stress of larger tires and rugged terrain.

• Fits 2018-2025 Jeep Wrangler JL Sahara models.
• Apex series design offers a low-profile, high-strength solution for axle reinforcement.
• Precision-engineered to contour to the factory rear axle for a secure fit.
• Helps prevent permanent axle damage during rock crawling or high-speed desert driving.
• Manufacturer Part Number: JL4502

Please note: This is a weld-on component and requires professional installation to ensure proper alignment and structural integrity.

Fits 2018-2025 Jeep Wrangler JL and Gladiator JT models equipped with a front Dana 44 axle.

Reinforce your front end for serious off-roading with the Artec Industries Apex Front Axle Truss. This heavy-duty reinforcement system is engineered to solve the common issue of axle tube bending and housing deflection that occurs when running larger tires or tackling aggressive terrain. The Apex series features a low-profile design that provides maximum clearance while adding significant structural rigidity to the factory housing.

Constructed from precision laser-cut steel, this truss is designed to wrap around the differential and extend along the axle tubes, distributing loads more effectively than the stock configuration. This is an essential upgrade for Jeep owners looking to maintain axle alignment and prevent catastrophic housing failure during high-torque or high-impact maneuvers.

• Specifically designed for the 2018-2025 Jeep JL and JT Dana 44 front axle
• Low-profile Apex design for improved suspension clearance
• Reinforces axle tubes and housing to prevent bending
• Precision CNC laser-cut and bent for a perfect fit
• Requires professional welding for installation
• Manufacturer Part Number: JL4501

Fits 2021-2025 Jeep Wrangler JL Sahara 2-Door models equipped with the 3.6L engine.

Shield your drivetrain from costly trail damage with the Artec Industries Full Aluminum Bellypan. Engineered to provide comprehensive underbody coverage, this skid plate system protects critical components like the engine, transmission, and transfer case from rocks and debris. Constructed from high-strength aluminum, it offers the impact resistance needed for serious off-roading without the significant weight penalty of traditional steel plating.

This bellypan is designed with maintenance in mind, featuring a dedicated oil door that allows you to perform routine oil changes without removing the entire assembly. It bolts directly to factory mounting points for a secure fit that maintains maximum ground clearance.

• High-grade aluminum construction for lightweight strength and corrosion resistance
• Full-length protection from the engine to the transfer case
• Integrated oil door simplifies routine engine maintenance
• Precision-engineered for the Jeep Wrangler JL 2-Door chassis
• All necessary mounting hardware included
• Manufacturer Part Number: JL4167

Fits 2018 Jeep Wrangler JL Sahara 4-Door (3.6L).

Protect your vehicle's vulnerable undercarriage from trail damage with the Artec Industries Full Bellypan. Precision-engineered from aluminum, this skid system offers comprehensive protection for critical drivetrain components while minimizing added weight. This bellypan includes an integrated oil door, allowing you to perform oil changes and routine maintenance without the labor-intensive process of removing the entire skid plate.

• Direct fit for 2018 Jeep Wrangler JL Sahara 4-Door models
• Lightweight aluminum construction provides durable underbody protection
• Integrated oil door simplifies maintenance and oil changes
• Designed to maximize ground clearance and protect the undercarriage
• Manufacturer Part Number: JL4125

Fits 2018-2025 Jeep Wrangler JL Sahara models equipped with the Dana 30 (D30) front axle.

The Artec Industries Apex Front Axle Truss is engineered to provide critical structural reinforcement for your Jeep's front end. Designed to address the factory housing's vulnerabilities, this truss helps prevent axle tube bending or shearing during heavy off-road use or when running larger tire diameters. The Apex series features a low-profile design that maintains necessary clearances while significantly increasing the rigidity of the Dana 30 housing.

• Specifically designed for Jeep Wrangler JL Sahara Dana 30 front axles
• Strengthens the axle housing to prevent bending under load or impact
• Low-profile Apex series geometry for maximum clearance
• Precision-engineered for a secure fit to factory axle contours
• Manufacturer Part Number: JL3101

Fits 2007-2018 Jeep Wrangler JK models equipped with a Dana 44 front axle.

The Artec Industries Apex Front Axle Truss (JK4451) provides essential structural reinforcement for your Dana 44 housing. This truss is designed to bridge the axle tubes and the differential center section, significantly increasing the axle's resistance to bending or shearing under the stress of off-road use, larger tire diameters, and heavy suspension loads.

• Precision-engineered for the 2007-2018 Jeep Wrangler JK Dana 44 front axle
• Apex series design optimizes the strength-to-weight ratio for maximum reinforcement
• Helps prevent permanent axle tube deflection and housing failure
• Low-profile construction designed to maintain clearance for suspension components
• Manufacturer Part Number: JK4451

Fits 2007-2018 Jeep Wrangler JK (2-Door and 4-Door) models. The Artec Industries Rear Track Bar Bracket (JK4426) is a heavy-duty solution designed to correct rear suspension geometry and restore the roll center on lifted Jeeps. Lifting your Wrangler often results in an off-center rear axle and steep track bar angles; this bracket provides the necessary correction to improve handling stability and reduce axle shift during articulation.

• Corrects rear roll center and restores proper axle alignment on lifted vehicles
• Designed to withstand high-stress off-road conditions and prevent bracket failure
• Essential for maintaining predictable handling characteristics on 2007-2018 JK models
• Precision-engineered for a secure fit to the factory axle housing
• Manufacturer Part Number: JK4426

Fits 2007-2018 Jeep Wrangler JK.

Artec Industries Heavy Duty Rear Axle Upper Control Arm (UCA) Brackets provide a rugged, high-strength solution for replacing or upgrading the factory mounts on your Jeep JK. These brackets are designed to withstand the stresses of off-road use, offering significantly more durability than the thin-gauge OEM components they replace. Whether you are repairing damaged factory mounts or building a custom axle, these HD brackets provide the structural integrity needed for demanding terrain.

• Heavy-duty construction designed for high-stress off-road applications.
• Direct replacement for weak factory upper control arm mounting points on the rear axle.
• Precision engineered for 2007-2018 Jeep Wrangler JK (2-door and 4-door) fitment.
• Includes one pair of brackets (driver and passenger side).
• Manufacturer Part Number: JK4424

Fits 2007-2018 Jeep Wrangler JK models.

These heavy-duty front axle lower control arm (LCA) brackets from Artec Industries are designed to replace or reinforce the vulnerable factory mounts on your Jeep JK. The factory brackets are known to bend or tear when subjected to off-road abuse or larger tire diameters. These replacements provide a much-needed upgrade for trail-ready rigs, ensuring your suspension geometry stays intact during technical crawling or high-speed desert runs.

• Direct replacement for factory front axle lower control arm brackets
• Engineered for off-road durability and rock clearance
• Sold as a complete pair (Driver and Passenger sides)
• Weld-on installation ensures maximum strength
• Manufacturer Part Number: JK4412

Fits 2007-2018 Jeep Wrangler JK.

The Artec Industries Heavy Duty Stock Tracbar Bracket (JK4407) is a high-strength replacement for the often-weak factory axle-side track bar mount. Designed to maintain factory steering geometry while offering significantly more rigidity than the thin OE bracket, this heavy-duty upgrade helps prevent the mounting hole wallowing and bracket flex that can contribute to front-end instability.

• Replaces weak factory axle-side track bar bracket in the stock location
• Heavy-duty construction provides superior durability for off-road use
• Helps eliminate steering play caused by bracket flex
• Engineered for precise fitment on 2007-2018 Wrangler JK models
• Manufacturer Part Number: JK4407

Fits 2007-2018 Jeep Wrangler JK models.

The Artec Industries Heavy Duty Raised Track Bar Bracket (JK4406) is engineered to optimize suspension geometry on lifted Jeep JKs. By raising the track bar's axle-side mounting point, this bracket helps restore the vehicle's roll center, significantly improving handling and reducing body roll during cornering. Precision-cut from heavy-duty steel, this bracket provides a far more robust mounting solution than the factory equipment, ensuring your axle remains properly centered under the stresses of off-road use.

• Fits 2007-2018 Jeep Wrangler JK
• Heavy-duty steel construction for maximum durability and strength
• Raised design improves roll center and suspension geometry on lifted vehicles
• Helps eliminate suspension bind and improves steering feel
• Replaces or reinforces weak factory axle brackets
• Manufacturer Part Number: JK4406

Fits 2007-2018 Jeep Wrangler JK.

Reinforce your front axle housing with Artec Industries Inner C Gussets (JK4405). The factory Dana 30 and Dana 44 axle housings on the Jeep JK are prone to bending at the inner C-knuckles when subjected to the stress of larger tires and off-road articulation. These gussets provide the necessary structural support to prevent axle deflection and costly housing damage.

• Engineered to reinforce the upper and lower factory inner C-knuckles
• Heavy-duty steel construction for maximum rigidity
• Precision-cut for a direct fit on Dana 30 and Dana 44 front axles
• Essential upgrade for Wranglers running 35-inch or larger tires
• Manufacturer Part Number: JK4405

Fits select 2007-2018 Jeep Wrangler JK models equipped with a Dana 30 front axle.

The Artec Industries Apex Front Axle Truss (JK3051) provides essential structural reinforcement for the factory Dana 30 housing, a necessary upgrade for JK owners running larger tires or tackling demanding off-road trails. This low-profile truss system is engineered to strengthen the factory axle tubes, effectively preventing the housing from bending or shearing under the high-stress loads encountered during technical wheeling.

• Precision CNC-cut and bent for an exact fit on the Dana 30 front axle assembly
• Low-profile design ensures maximum clearance for suspension components and steering geometry
• Heavy-duty construction reinforces the axle tubes to maintain long-term housing integrity
• Integrated design provides comprehensive support across the axle span
• Manufacturer Part Number: JK3051

Fits 2007-2018 Jeep Wrangler JK models performing a 1-ton axle conversion.

The Artec Industries Apex Rear 14 Bolt Truss Swap Kit (JK1415) is a heavy-duty fabrication solution for Jeep JK owners upgrading to a GM 14-bolt rear axle. This kit is engineered to provide the structural rigidity required for hardcore off-roading while simplifying the geometry needed to integrate a 1-ton axle into the JK chassis. The low-profile Apex design ensures maximum clearance without sacrificing the strength needed to prevent axle housing flex under high torque loads.

• Precision-engineered for GM 14-bolt rear axle tube fitment
• High-strength steel construction for maximum durability in extreme terrain
• Low-profile Apex series design for optimized suspension and floor clearance
• Provides indexed mounting points to streamline the swap process
• Designed for 2007-2018 Jeep Wrangler JK (2-Door and 4-Door)
• Manufacturer Part Number: JK1415

Fits 2007-2018 Jeep Wrangler JK (2-Door & 4-Door models).

The Artec Industries Spare Tire Delete Kit (JK1112) provides a professional, finished look for owners who have relocated their spare or are looking to shed weight and improve rear visibility. This kit replaces the bulky factory tire carrier with a sleek, low-profile plate that covers the venting and mounting holes in the tailgate.

Constructed from lightweight yet durable aluminum, this delete kit is designed to withstand the elements and the vibrations of off-road travel. The powdercoated finish adds a layer of corrosion protection while maintaining a clean aesthetic that complements the JK body lines. This plate bolts directly to the factory mounting points for a simple and secure installation.

• Material: Lightweight aluminum construction
• Finish: Durable powdercoat for long-term corrosion resistance
• Fitment: 2007-2018 Jeep Wrangler JK/JKU
• Installation: Reuses factory tailgate mounting locations
• Manufacturer Part Number: JK1112

Fits 2012-2018 Jeep Wrangler JK 4-Door models.

The Artec Industries Under Armor Bellypan Kit (JK1010) provides comprehensive underside protection for your Jeep Wrangler JK. This heavy-duty skid plate system is engineered to shield vital drivetrain components from trail obstacles, rocks, and debris, ensuring your vehicle remains operational in the most demanding off-road environments. Designed specifically for the updated drivetrain and exhaust layouts of the later JK models, this kit offers a high-clearance solution for maximum trail performance.

• Specifically designed for 2012-2018 4-door Jeep Wrangler JK models
• Provides full-length belly coverage to protect the engine, transmission, and transfer case
• Heavy-duty construction designed for extreme off-road impacts
• Low-profile design maintains maximum ground clearance
• Compatible with Artec Under Armor modular skid system components
• Manufacturer Part Number: JK1010

Fits 2018-2025 Jeep Wrangler JL and Gladiator JT models.

The Artec Industries High Clearance Comp Front Bumper with Hoop Guard (JJ8022) is engineered for off-roaders who prioritize maximum approach angles and front-end protection. This competition-inspired "stubby" bumper is designed to keep the front tires clear of obstructions, allowing for better articulation and clearance on technical trails and rock crawls.

• High-clearance competition design optimized for extreme approach angles
• Integrated hoop guard for added grille and winch protection
• Heavy-duty construction designed to withstand rigorous off-road use
• Direct fitment for Jeep Wrangler JL and Gladiator JT platforms
• Precision-engineered for reliable performance and trail durability
• Manufacturer Part Number: JJ8022

Fits 2005-2012 Ford F-250 and F-350 Super Duty models.

The Artec Industries Crossover Weld-On High Steer Arms are engineered to solve steering geometry challenges on lifted Super Duty trucks or vehicles utilizing late-model Super Duty axle swaps. These weld-on components provide a robust mounting point for a crossover steering configuration, moving the drag link higher to correct extreme angles and reduce bump steer.

Constructed for high-clearance applications, this kit is designed specifically to interface with the factory 2005-2012 Super Duty knuckle. By relocating the steering linkage above the leaf springs or suspension components, you gain better leverage and improved steering response on technical terrain. These arms are essential for builders seeking a heavy-duty, permanent solution for off-road steering performance.

• Fits 2005-2012 Ford F-250 and F-350 (Super Duty Knuckle)
• Enables crossover steering for improved drag link geometry
• Weld-on design for maximum strength and durability
• Precision-engineered for a secure fit to the factory casting
• Manufacturer Part Number: HS6150

Complete your suspension fabrication with the Artec Industries 4-Link Hardware Assembly Kit. Designed for builders using 1-1/4 inch rod ends or bushings, this comprehensive hardware package eliminates the guesswork of sourcing individual high-strength fasteners for a full 4-link setup.

This kit is engineered to provide the essential mounting hardware required to secure your upper and lower control arms to both the chassis and axle brackets. Each component is selected for the rigorous demands of off-road articulation and high-torque applications, ensuring your suspension geometry remains secure under stress.

• Manufacturer Part Number: HK0002
• Hardware Size: 1-1/4 inch (1.25")
• Application: Custom 4-Link Suspension Systems
• Optimized for use with Artec Industries link brackets and suspension components

The Artec Industries Bushing Kit (BU2003) is a heavy-duty solution for custom suspension fabrication, link ends, and chassis mounts. Built to withstand the rigors of off-road use, this kit provides a durable pivot point that helps dampen vibration while maintaining precise geometry.

• Mounting Width: 2.0 inches
• Sleeve Outer Diameter: 2.0 inches
• Bolt Hole Size: 1/2 inch
• Manufacturer Part Number: BU2003

Each kit is designed for easy welding and installation into custom control arms or track bars. The high-quality bushing material ensures long-lasting performance and resistance to environmental debris, making it an essential component for builders requiring reliable, high-tolerance hardware.

The Artec Industries Adjustable Link Tower provides a heavy-duty, weld-on mounting solution for custom 3-link and 4-link suspension systems. Specifically engineered for 3-1/4 inch (3.25") diameter axle tubes, this single tower allows fabricators to fine-tune suspension geometry and anti-squat characteristics through multiple mounting hole positions.

• Precision CNC laser-cut from high-strength steel for maximum durability
• Contoured base designed specifically for a flush fit on 3.25-inch axle tubes
• Multiple vertical mounting holes allow for precise link geometry adjustments
• Heavy-duty construction handles the high stress of off-road articulation
• Sold as a single unit (Manufacturer Part Number: BR1061)

Note: This component requires professional welding and fabrication for installation on the axle housing.

The Artec Industries Adjustable Inner Frame Bracket (BR1040) is a heavy-duty fabrication component designed for custom suspension builds. Engineered to provide a robust mounting point for link arms, this 25-degree bracket allows fabricators to optimize suspension geometry and axle positioning on custom chassis or axle-swapped vehicles.

• Optimized 25-degree angle for improved link clearance and suspension geometry.
• Adjustable mounting holes for fine-tuning anti-squat and roll center characteristics.
• Versatile fitment: Designed for Front Passenger or Rear Driver side applications.
• Professional-grade component for secure link-to-frame attachment.

This single bracket is an essential component for builders seeking precise control over their suspension cycle. As a weld-on part, it requires professional fabrication skills to ensure structural integrity and proper alignment with the vehicle's frame.

• Brand: Artec Industries
• Part Number: BR1040
• Angle: 25 Degrees
• Position: Front Passenger / Rear Driver
• Quantity: Single

The Artec Industries Adjustable Frame Panhard Mount (BR1027) is a precision-engineered suspension component designed for custom fabrication and heavy-duty off-road builds. This mount is specifically designed to be positioned on the outside of the frame rail, providing a robust attachment point for your track bar or panhard rod.

• Designed for use with 1.75-inch diameter tubing
• Adjustable mounting holes allow for fine-tuning suspension geometry to minimize bump steer
• Constructed for high-strength durability in demanding off-road environments
• Ideal for custom link suspension setups and chassis fabrication
• MPN: BR1027

By offering multiple mounting positions, this bracket ensures you can achieve the optimal roll center and geometry for your vehicle's specific lift height and axle configuration.

The Artec Industries BR1017 10-Degree Inner Frame Bracket is a precision fabrication component designed for builders constructing custom suspension geometries. This weld-on bracket is specifically angled at 10 degrees to optimize link placement on the inner frame rail, ensuring proper clearance and articulation for 3-link or 4-link setups.

• Manufacturer Part Number: BR1017
• Orientation: Front Passenger Side or Rear Driver Side
• Mounting Angle: 10-Degree
• Configuration: Inner Frame Mount
• Quantity: Sold Individually (Single)

This bracket is engineered for heavy-duty off-road use and provides a secure, professional mounting point for custom chassis work. As a weld-on component, it allows for maximum flexibility in suspension design and axle placement.