Fits select 2019-2026 Chevrolet Silverado, Colorado, and Suburban, GMC Sierra, and Ram 1500/2500/3500 trucks with 12-inch AAM axles.

Protect your drivetrain and extend lubrication life with the Banks Ram-Air Differential Cover. Unlike conventional flat-back aftermarket covers that can actually impede cooling, the patented Banks design utilizes high-velocity air scoops to force air through external heat radiation fins. This aerodynamic approach overcomes the "dead air zone" behind the differential, cooling up to 5X better than competing high-capacity covers in real-world towing conditions.

The interior is just as engineered as the exterior. A precision ring gear raceway guides fluid directly to the ring and pinion interface and out to the axle tubes and bearings, reducing aeration and ensuring consistent lubrication. Maintenance is simplified with an integrated sight glass for quick level checks, an angled fill port, and a magnetic drain plug to capture metallic wear particles. Installation is clean and reliable thanks to a reusable O-ring seal that eliminates the need for messy RTV silicone.

• Patented Forced-Air cooling design with break-away Ram-Air scoops
• Internal FlowThru Fins transfer heat to the exterior efficiently
• Maintains factory ground clearance and fluid capacity
• Sight glass for easy fluid level monitoring
• Magnetic drain plug and temp sensor port included
• High-quality black finish with O-ring seal
• Manufacturer Part Number: 19286

Fits 2017-2024 Ford F-250 and F-350 Super Duty SRW models equipped with the Dana M275 rear differential.

The Banks Power Ram-Air differential cover is engineered to extend lubrication life by significantly reducing fluid temperatures through superior aerodynamics. While many flat-back aftermarket covers can actually impede airflow and trap heat, the patented Banks design utilizes Ram-Air scoops to force high-velocity air through integrated heat radiation fins. In controlled 200 hp 60 mph sustained dyno tests, this system cooled 118% better than competitors, and up to 5X better in on-road towing scenarios.

• Patented Forced-Air Cooling: Integrated Ram-Air scoops and FlowThru Fins transfer heat directly from the fluid to the exterior air, overcoming the "dead air zone" behind the differential.
• Optimized Fluid Dynamics: Features a ring gear raceway that guides fluid to the ring and pinion interface and axle tubes while reducing fluid aeration.
• Simplified Maintenance: Includes a built-in sight glass for quick fluid level checks, an angled fill port, and a magnetic drain plug to capture ferrous wear particles.
• Premium Construction: Uses a reusable O-ring seal to eliminate the need for messy RTV and maintains factory ground clearance.
• Safety Engineered: The Ram-Air scoops are designed to break away if they strike an obstacle, protecting the differential housing from impact damage.

• Manufacturer Part Number: 19282
• Axle Application: Dana M275
• Seal Type: Silicone O-ring

Fits select 1962-2024 Ford F-250, F-350, Super Duty, Excursion, Bronco, and Maverick models (10.25in 12-Bolt).

The Banks Power Ram-Air Differential Cover (MPN 19262) is engineered to solve the inherent cooling deficiencies of standard flat-back aftermarket covers. While high-capacity covers often rely solely on increased oil volume, the patented Ram-Air system uses external scoops to force high-velocity air through integrated heat radiation fins. This design actively overcomes the "dead air zone" behind the differential housing, providing superior cooling during sustained high-load towing and highway driving.

Beyond thermal management, the internal geometry features a ring gear raceway that guides lubricant directly to the ring and pinion interface and out to the axle tube bearings. This ensures optimal lubrication even under extreme stress. Maintenance is simplified with a built-in sight glass, an angled fill port, and a magnetic drain plug to capture ferrous wear particles.

• Patented Ram-Air scoops force air through radiation fins for active cooling
• Internal FlowThru Fins transfer heat from the fluid to the exterior casing
• Ring gear raceway reduces fluid aeration and improves lubrication delivery
• High-strength magnetic drain plug and integrated fluid level sight glass
• Includes 1/8-inch NPT port for temperature sensor installation
• O-ring seal provides a leak-free fitment without the mess of RTV silicone
• Natural finish aluminum construction with 304 stainless steel hardware
• Designed to maintain factory ground clearance for off-road reliability

Fits 2011-2025 Ram 1500, 2500, and 3500 trucks (including Classic models).

When upgrading to a high-capacity aftermarket differential cover, clearance between the cover and the factory rear sway bar can become an issue. The Banks Power Sway Bar Spacer Kit (19249-2) provides the specific offset required to prevent rubbing and contact between the rear sway bar and the Banks Ram-Air Differential Cover. Engineered for Ram trucks equipped with rear coil sway bars, this kit allows for a clean installation and maintains full suspension articulation without interference.

• Prevents rear sway bar from rubbing against the Banks Differential Cover
• Direct bolt-on application requires no cutting, welding, or modification to the axle
• Maintains proper suspension geometry for trucks with rear coil-spring sway bars
• Includes all necessary high-strength mounting hardware
• Manufacturer Part Number: 19249-2

Fits select 1999-2014 Dodge/Ram 2500/3500 and Chevrolet/GMC Silverado/Sierra 2500 HD/3500 heavy-duty trucks equipped with the 14-bolt 11.5-inch American Axle (AAM) rear end.

The ATS Diesel Protector Rear Differential Cover is engineered to provide superior protection and cooling for high-torque towing and heavy-duty applications. Designed specifically for the 11.5-inch AAM axle found in many 3/4-ton and 1-ton GM and Ram pickups, this cover increases fluid capacity compared to the factory unit. The cast construction and cooling fins help dissipate heat more effectively, extending the life of your gear oil and internal components while adding structural rigidity to the axle housing.

• Fits 14-bolt 11.5-inch American Axle (AAM) rear differentials
• Enhanced cooling capacity via integrated heat-dissipating fins
• Increased oil volume for better thermal management
• Durable cast construction for maximum housing protection
• Direct-fit replacement for the OE cover
• Manufacturer Part Number: 402-915-6248

Fits select 1983-2010 Ford F-150, F-250, F-350, F-250/F-350 Super Duty, Excursion, and E-Series models with the Sterling 10.25-inch 12-bolt axle.

The ATS Diesel Ford Sterling 10.25-inch Differential Cover is a heavy-duty upgrade designed to provide superior protection for your truck's drivetrain. By replacing the factory stamped-steel cover, this 12-bolt unit increases the structural integrity of the rear axle housing, helping to maintain precise gear alignment under heavy towing loads or high-torque conditions. Engineered for durability, it is an essential component for diesel and gas Ford trucks and vans that see heavy use.

• Specifically designed for Ford Sterling 10.25" ring gear axles
• 12-bolt mounting pattern for a secure, high-pressure seal
• Robust construction helps dissipate heat and resists impact damage
• Replaces thin factory OE covers for improved housing rigidity
• Manufacturer Part Number: 402-900-3068

Fits select 2018-2025 Ford Bronco, Ford Ranger, Jeep Wrangler (JL), and Jeep Gladiator (JT) equipped with the Dana M220 rear axle.

Protect your drivetrain from trail damage with the ARB Competition Differential Cover. Engineered to withstand the rigors of extreme off-road use, this cover replaces the thin factory stamped-steel plate with a high-strength nodular iron structure. The cross-braced design not only shields the ring and pinion set but also provides additional housing stiffness, reducing flex under load and prolonging carrier bearing life. This cover is finished in a durable black powder coat for long-term corrosion resistance.

• Manufacturer Part Number: 0750012B
• Compatible Axle: Dana M220
• Material: High-strength nodular iron for impact protection
• Recessed tensile cap screws protect bolt heads from rock rash and shearing
• Low-profile drain plug design minimizes the risk of snagging on obstacles
• Integrated dipstick with high-power neodymium magnets collects metallic wear particles
• Computer-optimized cross-brace design increases structural rigidity
• Optimized approach and departure angles for maximum clearance

Fits select 2018-2025 Jeep Wrangler (JL), 2020-2025 Jeep Gladiator (JT), 2021-2025 Ford Bronco, and 2019-2023 Ford Ranger models equipped with the M220 rear axle.

The ARB M220 Differential Cover is engineered to protect your ring and pinion set from the structural damage common during technical off-roading. Cast from high-tensile nodular iron, this cover reinforces the entire axle housing, reducing flex under load and prolonging carrier bearing life. Its computer-optimized cross-brace design improves the structural integrity of the differential while maintaining maximum clearance for optimized approach and departure angles.

• Cast from high-tensile nodular iron for superior impact resistance and housing rigidity.
• Recessed tensile cap screws are protected from rock damage and shearing on trail obstacles.
• Low-profile drain plug design resists damage and minimizes snags.
• Integrated dipstick with high-strength neodymium magnet allows for easy oil level checks and collects metallic wear particles.
• Durable red powder-coated finish for maximum corrosion resistance.
• Includes high-quality neodymium magnets in both the dipstick and drain plug.
• Manufacturer Part Number: 0750012.

Fits 2018-2025 Jeep Wrangler (JL) and 2020-2025 Jeep Gladiator (JT) across all trims including Rubicon, Mojave, Sahara, and Sport.

Engineered to withstand the rigors of extreme off-road use and competition, the ARB Competition Differential Cover provides essential protection for your ring and pinion set and differential internals. This cover is cast from high-tensile nodular iron to provide maximum protection against rock strikes and impacts while increasing the structural rigidity of the entire axle housing to prevent flex under load.

• High-tensile iron construction protects the differential, ring and pinion, and locker from impact damage
• Recessed high-tensile cap screws are shielded from obstacles to prevent bolt-head shearing
• Integrated dipstick with high-strength neodymium magnets monitors oil levels and collects metallic wear particles
• Computer-optimized cross-brace design increases housing strength and extends carrier bearing life
• Low-profile drain plug design resists damage and minimizes snags on the trail
• Durable black powder-coated finish for superior corrosion resistance
• Part Number: 0750011B

Fits select 2018-2025 Jeep Wrangler (JL) and 2020-2025 Jeep Gladiator (JT) models.

Protect your drivetrain from expensive impact damage with the ARB Differential Cover. Cast from high-tensile nodular iron, this cover is engineered to shield the ring and pinion set from rocks and off-road hazards. The computer-optimized cross-brace design increases the structural rigidity of the entire axle housing, providing additional support to the carrier bearings and prolonging their service life during heavy-duty use.

Every detail is designed for the trail, featuring a low-profile drain plug and recessed cap screws to prevent damage from contact with obstacles. For easier maintenance, a high-quality Neodymium magnetic dipstick is integrated into the fill plug, allowing you to check oil levels and inspect for internal wear without removing the cover. Finished in a durable powder coating for long-lasting corrosion resistance.

• Manufactured from high-tensile nodular iron for maximum impact resistance
• Powder-coated finish for superior durability
• Computer-optimized cross-brace design increases housing strength
• Recessed cap screws and low-profile drain plug resist trail damage
• Neodymium magnetic dipstick for oil level checks and wear debris collection
• Prolongs carrier bearing life via increased support
• Manufacturer Part Number: 0750011

Fits select 2018-2025 Jeep Wrangler models with the Front M186 axle. This includes Sport, Sport S, Sahara, Rubicon, and Willys trims across both 2-door and 4-door Unlimited configurations.

The ARB Front M186 Differential Cover is engineered to protect your axle internals and ring and pinion set from the hazards of extreme off-roading. Built from a high-tensile iron structure with a computer-optimized cross-brace design, this cover increases the structural rigidity of the entire axle housing. This added stiffness provides essential support for the carrier bearings, effectively prolonging their service life and ensuring gears remain in correct alignment under high-load conditions.

• High-tensile iron construction protects against impacts and rock damage.
• Recessed high-tensile cap screws are shielded from obstacles to prevent shearing or damage.
• Low-profile drain plug design minimizes the risk of snagging on trail debris.
• Integrated magnetic dipstick with high-strength Neodymium magnets collects metallic wear particles.
• Optimized approach and departure angles for maximum clearance in technical terrain.
• Durable powder-coated finish for long-term corrosion resistance.
• MPN: 0750009

Fits select 2000-2017 Nissan Frontier, Titan, Xterra, and Suzuki Equator equipped with the Dana M226 axle.

The ARB Differential Cover is engineered to protect your ring and pinion set from the severe impacts of off-road hazards. Cast from high-tensile nodular iron, this cover (MPN 0750008B) adds significant structural integrity to the entire axle housing. Its computer-optimized cross-brace design increases the rigidity of the carrier, prolonging bearing life by reducing housing flex under heavy torque loads.

Built for the trail, this cover features recessed cap screws and a low-profile drain plug to prevent shearing or damage from rocks. For maintenance ease, ARB includes a high-quality Neodymium magnetic dipstick and drain plug to collect metallic wear particles, allowing you to monitor the internal health of your differential between fluid changes.

• Manufactured from high-tensile nodular iron for maximum impact resistance
• Computer-optimized cross-brace design increases overall housing strength
• Recessed high-tensile cap screws protect against rock-induced shearing
• High-power Neodymium magnets integrated into the dipstick and drain plug
• Low-profile drain plug design maximizes clearance on technical terrain
• Durable black powder-coated finish for corrosion resistance
• Specifically designed for use with Nissan/Dana M226 axle housings
• Manufacturer Part Number: 0750008B

Fits select 2000-2017 Nissan Frontier, Titan, Xterra, and Suzuki Equator equipped with the Dana M226 rear axle. The ARB Differential Cover is engineered from high-tensile nodular iron to protect your ring and pinion set from impact and expensive off-road damage.

This heavy-duty cover features a computer-optimized cross-brace design that increases the structural rigidity of the entire axle housing. By reducing housing flex, it provides additional support to the carrier bearings, prolonging gear life and improving mesh under load. For maintenance, the integrated dipstick features a high-strength neodymium magnet to capture metallic wear particles, while the recessed cap screws and low-profile drain plug are shielded from trail obstacles.

• Manufactured from high-tensile nodular iron for maximum impact resistance
• Computer-optimized cross-brace design adds housing strength and reduces bearing deflection
• Recessed cap screws and low-profile drain plug prevent damage from rocks and hazards
• Integrated dipstick with neodymium magnet for fluid level checks and debris collection
• Durable powder-coated finish for long-term corrosion protection
• Includes high-tensile cap screws
• Manufacturer Part Number: 0750008

Fits select 1980-2012 Chevrolet and GMC C1500/K1500, Blazer, Tahoe, Yukon, and Colorado (10-Bolt).

The ARB differential cover is engineered to safeguard your ring and pinion set from the impact of rocks and off-road hazards. Cast from high-tensile nodular iron, this cover adds significant structural rigidity to the entire axle assembly. This increased strength helps prevent the housing from flexing under load, reducing carrier bearing deflection and extending the life of your internal components.

• Nodular Iron Construction: High-tensile iron structure protects the differential and ring and pinion set from impact damage.
• Computer-Optimized Cross-Brace Design: Increases housing strength while optimizing approach and departure angles for trail clearance.
• Recessed Hardware: Tensile cap screws are recessed to prevent damage or shearing when encountering obstacles.
• Magnetic Drain Plug & Dipstick: Includes a high-quality Neodymium magnetic dipstick and drain plug to capture metallic wear particles and allow for easy fluid level inspection.
• Low-Profile Design: The drain plug is designed to resist damage and prevent leaking during heavy off-road use.
• Durable Finish: Powder coated black for maximum corrosion resistance and longevity.

Manufacturer Part Number: 0750007B

Fits select 1980-2012 Chevrolet and GMC trucks and SUVs, including Blazer, Tahoe, Yukon, C1500, K1500, Colorado, and Canyon with the 10-bolt differential.

Protect your drivetrain from off-road hazards with the ARB 10-Bolt Differential Cover. Cast from high-tensile nodular iron, this cover is engineered to significantly increase the structural rigidity of the entire axle assembly. By reducing carrier bearing deflection under load, it helps maintain proper ring and pinion gear mesh for increased longevity and reliability on the trail. The computer-optimized cross-brace design and approach/departure angle clearance ensure your differential stays protected without snagging on obstacles.

• High-tensile nodular iron construction provides superior impact protection
• Recessed cap screws are shielded from rock damage and shearing
• Magnetic dipstick with a high-strength neodymium magnet monitors oil level and traps metal particles
• Additional housing strength reduces carrier bearing deflection during high-torque events
• Low-profile drain plug design resists damage from trail hazards
• Durable red powder-coated finish for corrosion resistance
• Manufacturer Part Number: 0750007

Fits select 1983-2014 Ford Bronco, Crown Victoria, E-Series, Expedition, Explorer, F-150, F-250, and Ranger, along with Mazda B4000 and Navajo models equipped with the 8.8-inch axle.

Protect your drivetrain from trail damage with the ARB 0750006B Differential Cover. Engineered for off-road durability, this cover is cast from high-tensile nodular iron to shield the ring and pinion set from impact. Beyond pure protection, the iron structure and computer-optimized cross-bracing increase overall housing strength, providing extra support to the carrier bearings and preventing gear deflection under high-torque loads.

The design features recessed cap screws and a low-profile drain plug to prevent snagging on rocks or obstacles. For maintenance, a built-in dipstick with high-strength neodymium magnets allows you to check oil levels and inspect for internal wear by collecting metallic particles from the fluid.

• Manufacturer Part Number: 0750006B
• High-tensile nodular iron construction for superior impact resistance
• Black powder-coated finish for long-lasting corrosion protection
• Magnetic dipstick with neodymium magnets to trap metallic debris
• Recessed cap screws protected against trail hazards
• Low-profile drain plug design minimizes obstacle damage
• Computer-optimized cross-brace design increases housing rigidity
• Optimized approach/departure angles for improved clearance