Calibrate your turbocharger system's response with this authentic TiAL Sport replacement spring, specifically designed for Q and QR series blow off valves. This 10 PSI spring (color-coded Black) is a critical tuning component used to match the valve's opening pressure to your engine's vacuum characteristics, ensuring the BOV remains seated at idle while providing rapid pressure relief under deceleration.

• Compatible with TiAL Sport Q and QR series blow off valves
• Spring Pressure Rating: 10 PSI (-20 in/Hg)
• Color Code: Black for easy identification
• High-strength spring steel construction for consistent tension and longevity
• Helps prevent compressor surge and boost leaks caused by incorrect spring rates
• Manufacturer Part Number: 002568

This genuine TiAL Sport replacement spring is engineered specifically for use within Q and QR Series Blow Off Valves (BOV). In a vacuum-actuated bypass system, the spring rate is critical for ensuring the valve remains closed at idle while allowing for rapid venting during lift-off. This Blue-coded spring is rated for 10 PSI, providing the specific tension required to match your engine's vacuum profile and prevent compressor surge.

• Manufacturer Part Number: 002567
• Application: TiAL Q and QR Series Blow Off Valves
• Spring Rate: 10 PSI
• Color Identifier: Blue
• Material: High-strength spring steel for consistent tension and heat resistance
• Designed to maintain a precise seal under high boost pressures

The TiAL Sport GT30 .82 A/R Stainless Steel Turbine Housing is a premium upgrade for GT30 series turbochargers, engineered to provide superior thermal management and weight reduction over traditional cast-iron alternatives. Manufactured from high-grade stainless steel, this housing (MPN 002460) resists corrosion and maintains structural integrity under the extreme exhaust gas temperatures found in high-performance applications.

With a .82 A/R ratio, this housing offers an ideal balance between low-end responsiveness and high-RPM flow capacity. The stainless steel construction not only sheds weight but also improves heat retention, keeping exhaust energy focused on the turbine wheel for efficient spool-up. This is an essential component for custom turbo setups where durability and precision are paramount.

• Manufacturer Part Number: 002460
• Turbocharger Series: TiAL GT30
• A/R Ratio: .82
• Material: Stainless Steel
• Construction: High-heat resistant housing

Calibrate your turbocharger system’s pressure relief with this genuine TiAL Sport replacement spring. This 10 PSI spring is engineered specifically for the TiAL Q and QR series 50mm blow-off valves (BOV), allowing you to tune the valve's response to match your engine's specific manifold vacuum at idle. Selecting the correct spring rate is critical to ensure the valve remains closed under idle while still opening quickly under lift-off conditions to prevent compressor surge.

• Compatible with TiAL Q and QR series blow-off valves
• Spring Rate: 10 PSI (typically for engines with -16 to -19 in/Hg idle vacuum)
• Color Code: Silver for easy identification
• High-quality spring steel construction for consistent tension and longevity
• Manufacturer Part Number: 002115

The TiAL Sport MVS Wastegate is the industry standard for compact, reliable boost control in high-performance turbocharged applications. Engineered to fit into tight engine bays where space is at a premium, the MVS (38mm) design features integrated water-cooling ports to maintain stable diaphragm temperatures in extreme racing conditions. This kit (MPN: 001931) comes finished in silver and includes a full set of springs, allowing you to calibrate your boost level precisely for your specific setup.

• High-temperature NiCrFe based alloy used for the valve and 347SS housing for maximum lifespan under high EGTs.
• Compact design with a total height of only 3.7 inches.
• Integrated -4AN water cooling ports (optional use) to protect the actuator from heat soak.
• V-band inlet and outlet flanges for easy installation and a leak-free seal.
• Includes all available springs for versatile boost pressure configurations.
• Genuine TiAL Sport V-band clamps and air fittings included.

Enhance your engine's cooling and octane performance with the Snow Performance SNO-N3500 Water Methanol Injection Nozzle. Engineered for precise delivery, this 35 GPH nozzle utilizes a high-pressure atomization process to create a fine mist, ensuring complete evaporation as it enters the intake air stream.

By injecting a water-methanol mixture, this component helps drastically reduce Exhaust Gas Temperatures (EGTs) and suppresses engine detonation (knock), allowing for more aggressive timing or higher boost levels in forced induction applications. Its precision-machined construction ensures consistent flow rates and a reliable spray pattern under high-pressure conditions.

• Flow Rate: 35 GPH (Gallons Per Hour)
• Function: High-atomization water-methanol injection
• Construction: Precision-machined for durability and consistency
• Manufacturer Part Number: SNO-N3500
• Optimizes cooling and suppresses detonation for improved performance

The Snow Performance SNO-N3000 is a high-capacity water-methanol injection nozzle designed to deliver precise fluid atomization for high-output cooling. Engineered to suppress detonation and lower intake air temperatures (IATs), this nozzle ensures the water-methanol mixture is converted into a fine mist for rapid evaporation within the intake tract.

• Part Type: Water-Methanol Injection Nozzle
• Flow Rate: 30 GPH (Gallons Per Hour)
• Manufacturer Part Number: SNO-N3000
• Function: Precision atomization for maximum cooling and octane enhancement
• Compatibility: Replaces or adds to any standard Snow Performance injection system

The Snow Performance SNO-N2500 is a high-flow water-methanol injection nozzle designed to provide precise fluid atomization for high-horsepower forced induction applications. Rated at 25 GPH (Gallons Per Hour), this nozzle is engineered to withstand the pressures of high-output pumps while ensuring a consistent, fine mist for effective intake charge cooling and octane enhancement.

Constructed for durability and precision, this nozzle helps prevent pre-detonation (knock) and allows for more aggressive ignition timing by significantly reducing intake air temperatures. It serves as a critical component for any performance water-meth system, ensuring even distribution within the intake tract.

• Manufacturer Part Number: SNO-N2500
• Flow Rate: 25 GPH (Gallons Per Hour)
• Compatibility: Standard Water-Methanol Injection Systems
• Construction: Precision-machined for optimal spray pattern and atomization
• Function: Replaces worn nozzles or scales up system flow capacity

The Snow Performance Water Methanol Injection Nozzle (SNO-N2000) is engineered to provide precise fluid atomization for high-output cooling and octane enhancement. Rated at 20 GPH, this nozzle is a critical component for high-horsepower forced induction or high-compression engines, ensuring the water-methanol mixture is finely misted into the intake stream to effectively lower intake air temperatures and suppress detonation.

• Manufacturer Part Number: SNO-N2000
• Flow Rate: 20 GPH (Gallons Per Hour)
• Optimized spray pattern for superior fluid atomization
• Designed for use with Snow Performance water-methanol injection systems

The Snow Performance SNO-N1800 Water Methanol Injection Nozzle is engineered to provide precise fluid delivery for forced induction or high-compression naturally aspirated engines. Rated at 18 GPH, this nozzle is a critical component for achieving superior atomization, which is essential for effective intake air temperature (IAT) reduction and knock suppression.

Designed with a proprietary internal geometry, this nozzle creates a fine, uniform mist to ensure even distribution within the intake tract. This maximizes the cooling effect and effective octane boost provided by your water-methanol mixture. Whether you are replacing a worn nozzle or scaling your system for higher power levels, the SNO-N1800 delivers consistent performance under high pressure.

• Manufacturer Part Number: SNO-N1800
• Flow Rate: 18 GPH (Gallons Per Hour)
• Purpose-built for water-methanol injection systems
• Optimized spray pattern for maximum heat absorption

Ensure maximum atomization and intake cooling with this precision-machined 16 GPH nozzle from Snow Performance. Designed for high-output water-methanol injection systems, this nozzle is engineered to break down fluid into a fine, consistent mist, preventing intake puddling and ensuring even distribution across the cylinders.

Built to withstand the high pressures of performance WMI pumps and the corrosive nature of methanol, the SNO-N1600 nozzle is a critical component for maintaining safe combustion temperatures and increasing effective octane in forced induction or high-load applications. This component replaces worn or clogged nozzles to restore system efficiency and spray pattern integrity.

• Flow Rate: 16 GPH (Gallons Per Hour)
• Precision-machined design for superior fluid atomization
• Compatible with all Snow Performance water-methanol injection kits
• Robust construction for long-term durability and chemical resistance
• Manufacturer Part Number: SNO-N1600

Ensure consistent cooling and octane enhancement with the Snow Performance 14 GPH water-methanol injection nozzle. This precision-machined component is engineered to provide superior fluid atomization, which is critical for reducing intake air temperatures and preventing detonation in high-performance forced induction applications.

Designed as a direct replacement or expansion for existing Snow Performance systems, the SNO-N1400 nozzle delivers a reliable 14 GPH flow rate. Its robust construction resists clogging and maintains a stable spray pattern under high pressure, ensuring your engine receives the precise volume of methanol-water mix required for peak efficiency.

• Flow Rate: 14 GPH (Gallons Per Hour)
• Manufacturer Part Number: SNO-N1400
• Precision-machined for optimized spray atomization
• Compatible with standard Snow Performance nozzle holders
• Essential for high-horsepower cooling and knock suppression

The Snow Performance SNO-N1200 is a precision-engineered water-methanol injection nozzle designed to provide maximum atomization for performance-oriented cooling. Rated at a flow of 12 GPH, this nozzle is built to withstand the pressures of high-output WMI systems while ensuring a consistent, fine mist is delivered into the intake air stream to reduce intake air temperatures (IATs) and suppress detonation.

• Flow Rate: 12 GPH (Gallons Per Hour)
• Engineered for superior atomization to improve octane boost and cooling efficiency
• Precision machined for a consistent and repeatable spray pattern
• Compatible with all Snow Performance water-methanol injection kits and most 1/8-NPT nozzle holders
• Manufacturer Part Number: SNO-N1200

The Snow Performance SNO-N1000 is a precision-engineered water-methanol injection nozzle designed to deliver a metered flow of 10 GPH (Gallons Per Hour). This component is essential for achieving proper fluid atomization, ensuring the water-methanol mist is fine enough to flash-evaporate, effectively reducing intake air temperatures and suppressing detonation.

Constructed for durability and consistent performance under high pressure, this nozzle helps prevent fluid pooling and ensures even distribution within the intake tract. It serves as a direct replacement or an incremental upgrade for Snow Performance injection systems requiring specific flow scaling to match engine displacement and boost levels.

• Flow Rate: 10 GPH (Gallons Per Hour)
• Optimized for superior fluid atomization and intake cooling
• Precision-machined for a consistent spray pattern
• Replaces or upgrades existing water-meth nozzles
• Manufacturer Part Number: SNO-N1000

The Snow Performance SNO-N0900 is a precision-engineered water-methanol injection nozzle designed to deliver a consistent, finely atomized mist into the intake tract. Rated at a flow rate of 9 GPH (gallons per hour), this nozzle is a critical component for heat management and detonation control in high-performance forced induction or high-compression applications.

Constructed for durability and consistent spray patterns under high pressure, this nozzle helps reduce intake air temperatures (IATs) and increases effective fuel octane. It is designed for seamless integration with Snow Performance water-methanol systems and serves as an ideal replacement or upgrade for tuned engines requiring specific fluid volume delivery.

• Manufacturer Part Number: SNO-N0900
• Flow Rate: 9 GPH
• Function: High-pressure fluid atomization
• Application: Water-methanol injection systems
• Construction: Precision-machined for consistent spray patterns

Ensure optimal atomization and cooling in your forced induction or high-compression engine with the Snow Performance 8 GPH Water-Methanol Injection Nozzle. This precision-machined component is engineered to deliver a fine mist of water-methanol mixture into the intake stream, effectively reducing intake air temperatures (IATs) and suppressing detonation for increased power and engine safety.

Designed for use with all Snow Performance water-methanol injection systems, this nozzle is a critical component for maintaining consistent performance. The 8 GPH flow rate is typically utilized in mid-to-high horsepower applications where significant cooling and octane enhancement are required. This part serves as either a direct replacement for a worn nozzle or as part of a multi-nozzle configuration.

• Flow Rate: 8 GPH (Gallons Per Hour)
• Manufacturer Part Number: SNO-N0800
• Function: High-pressure fluid atomization for intake cooling
• Build Quality: Precision-machined for consistent spray patterns and durability

The Snow Performance SNO-N0700 Water-Methanol Injection Nozzle is engineered to provide precise fluid atomization for forced induction and high-compression engines. Rated at 7 GPH (Gallons Per Hour), this nozzle is a critical component for cooling intake charge temperatures and increasing effective octane levels when under load.

Constructed for durability and consistent spray patterns, it ensures a uniform mist that mixes thoroughly with the air stream. Whether you are replacing a worn nozzle or fine-tuning your system for specific power levels, this 7 GPH unit offers the reliability required for high-performance applications.

• Flow Rate: 7 GPH
• Precision-machined for fine fluid atomization
• Compatible with Snow Performance water-methanol injection kits
• Manufacturer Part Number: SNO-N0700

The Snow Performance SNO-N0600 is a precision-engineered water-methanol injection nozzle designed to provide consistent fluid atomization for high-performance cooling. Rated at 6GPH (gallons per hour), this nozzle is a critical component for reducing intake air temperatures and increasing effective octane levels to suppress detonation in forced induction or high-compression engines.

Built for durability and accuracy, these nozzles feature a specialized internal design to ensure a fine mist, promoting complete evaporation within the intake tract. They are fully compatible with all Snow Performance water-methanol injection systems and are 100% methanol resistant to prevent corrosion or degradation over time.

• Flow Rate: 6GPH (Gallons Per Hour)
• Compatibility: 100% Methanol resistant
• Construction: Precision-machined orifice for consistent misting
• Application: Replaces or adds capacity to existing WMI systems
• Manufacturer Part Number: SNO-N0600

Optimize your water-methanol injection system's efficiency with this Snow Performance 5 GPH nozzle (SNO-N0500). Designed for precise fluid atomization, this nozzle ensures a fine, uniform mist is introduced into the intake tract to effectively lower intake air temperatures and increase the effective octane of your fuel mixture.

• Flow Rate: 5 GPH (Gallons Per Hour) for consistent delivery
• Precision-machined design ensures a superior spray pattern for maximum evaporation
• Critical for suppressing detonation and protecting engines under high load
• Compatible with all Snow Performance water-methanol injection systems
• Manufacturer Part Number: SNO-N0500

The Snow Performance SNO-N0400EX is a 2 GPH (Gallons Per Hour) extended water/methanol injection nozzle designed for precise fluid atomization and distribution. The extended design of this nozzle allows the spray tip to reach further into the intake tract, ensuring the atomized mist is centered within the high-velocity airflow for more consistent cooling and combustion stabilization.

• Flow Rate: 2 GPH (Gallons Per Hour)
• Nozzle Type: Extended reach for improved spray placement
• Application: Compatible with most water-methanol injection systems
• Function: Atomizes fluid to reduce intake temperatures and suppress detonation
• Manufacturer Part Number: SNO-N0400EX

By optimizing the spray pattern and placement within the intake, this extended nozzle helps maximize the effective octane increase and cooling benefits of your water-meth system, particularly in forced induction or high-compression applications.

The Snow Performance 4 GPH Water Methanol Injection Nozzle (SNO-N0400) is a precision-engineered component designed to provide optimal atomization for your water-meth system. By creating a fine, consistent mist, this nozzle ensures maximum evaporation in the intake tract, which is critical for effectively lowering intake air temperatures (IATs) and increasing the effective octane of your fuel mixture.

Constructed to exacting tolerances, this nozzle is a direct replacement or expansion component for Snow Performance systems. It helps prevent hot spots and detonation, allowing for more aggressive timing or higher boost levels in forced induction applications.

• Flow Rate: 4 GPH (Gallons Per Hour)
• Precision machined for a consistent spray pattern and fine atomization
• Helps reduce intake air temperatures and suppress engine knock
• Compatible with all Snow Performance water-methanol injection kits
• Manufacturer Part Number: SNO-N0400

The Snow Performance 3.5 GPH water-methanol injection nozzle (SNO-N0350) is a precision-engineered component designed to optimize the performance of your injection system. By delivering a finely atomized mist into the intake tract, this nozzle facilitates efficient evaporation, which significantly reduces intake air temperatures and increases effective octane to suppress engine detonation.

Constructed for durability and consistent flow, this nozzle is essential for tuners looking to maintain safety and power in forced induction or high-compression applications. Its internal design is specifically calibrated to ensure a uniform spray pattern for maximum cooling effect.

• Flow Rate: 3.5 Gallons Per Hour (GPH)
• Optimizes intake air cooling and knock suppression
• Precision-machined for superior fluid atomization
• Manufacturer Part Number: SNO-N0350

The Snow Performance 3 GPH Water Methanol Injection Nozzle (SNO-N0300) is engineered for precision atomization in high-performance cooling systems. This nozzle is a critical component for reducing intake air temperatures (IATs) and suppressing detonation, allowing for increased timing or boost in forced induction and high-compression naturally aspirated applications.

Designed to handle the high pressures typical of water-methanol systems, this nozzle produces a fine mist that evaporates quickly in the intake tract for maximum cooling efficiency. It features a robust construction and an internal filter screen to prevent debris from clogging the orifice, ensuring a consistent spray pattern and reliable flow over time.

• Flow Rate: 3 GPH (Gallons Per Hour)
• Manufacturer Part Number: SNO-N0300
• Component Type: High-pressure atomizing nozzle
• Precision-machined for consistent spray delivery
• Integrated internal screen to protect against contaminants

Optimize your water-methanol system with the Snow Performance 2.5 GPH Water Methanol Injection Nozzle (SNO-N0250). Engineered for precision fluid atomization, this nozzle is a critical component for reducing air intake temperatures and increasing the effective octane rating of your fuel. By creating a fine mist, it ensures efficient evaporation within the intake tract to help prevent pre-ignition and detonation in high-performance or forced induction applications.

Constructed to maintain consistent flow even under high-pressure conditions, this nozzle is an ideal choice for fine-tuning your injection system's delivery to match your engine's displacement and power levels.

• Flow Rate: 2.5 Gallons Per Hour (GPH)
• Designed for superior atomization and cooling efficiency
• Compatible with all Snow Performance water-methanol kits
• Precision-machined for reliable, consistent delivery
• Manufacturer Part Number: SNO-N0250

The Snow Performance Hyper-Sonic Water-Methanol Injection Nozzle is engineered to provide the fine atomization required for effective intake charge cooling and detonation suppression. This 2 GPH (Gallons Per Hour) nozzle features a specialized internal design that breaks down fluid into a micro-mist, ensuring even distribution and maximum evaporation within the air stream for improved engine performance under boost.

• Flow Rate: 2 GPH (Gallons Per Hour)
• Atomization: Hyper-Sonic technology for superior fluid breakdown
• Compatibility: Designed for use with all Snow Performance water-methanol injection kits
• Filtering: Integrated 100-micron screen to prevent orifice clogging
• Mounting: Standard 1/8-inch NPT threading for a secure, leak-free fit
• Manufacturer Part Number: SNO-N0200

Constructed from materials resistant to the corrosive properties of methanol, this nozzle is a critical component for maintaining consistent delivery and cooling efficiency in forced induction or high-compression applications.

The Snow Performance SNO-N0150 is a precision-machined water-methanol injection nozzle designed to deliver a consistent 1.5 GPH (gallons per hour) flow rate. This component is critical for atomizing water-methanol mixtures into a fine, uniform mist, facilitating maximum heat absorption and helping to suppress detonation in high-compression or forced induction applications.

• Flow Rate: 1.5 GPH
• Engineered for superior fluid atomization and cooling efficiency
• Direct replacement or expansion nozzle for Snow Performance injection kits
• Precision-machined internal geometry for consistent spray patterns
• Manufacturer Part Number: SNO-N0150

The Snow Performance 1 GPH Water-Methanol Injection Nozzle is designed to provide the precise atomization required for effective intake charge cooling and octane enhancement. As a critical component of any methanol injection system, this nozzle ensures that the fluid is broken down into a fine mist for rapid flash-evaporation in the intake tract, significantly reducing air intake temperatures (IATs) and suppressing detonation.

Built to withstand the corrosive properties of high-concentration methanol mixtures, this nozzle is precision-machined to maintain a consistent spray pattern across various pressure ranges. Sizing your nozzle correctly is vital to matching your engine's specific horsepower and displacement needs, ensuring maximum performance without the risk of engine quenching.

• Flow Rate: 1 GPH (Gallons Per Hour)
• Engineered for superior fluid atomization and spray consistency
• Durable construction compatible with water and methanol mixtures
• Replaces or upgrades existing water-meth nozzles
• Manufacturer Part Number: SNO-N0100

The Snow Performance SNO-N0075 water-methanol injection nozzle is engineered for precision fluid delivery and superior atomization. This nozzle is designed with a hyper-sonic internal profile to produce a fine mist that flashes off instantly, effectively reducing intake air temperatures and suppressing detonation in forced induction or high-compression applications.

• Flow Rate: 0.75 GPH (Gallons Per Hour)
• Hyper-sonic design for optimized fluid atomization
• Compatible with water and methanol mixtures
• Precision-machined construction for consistent flow rates
• Manufacturer Part Number: SNO-N0075

Optimize your water-methanol system with the Snow Performance 0.5 GPH injection nozzle (SNO-N0050). Engineered for precise fluid delivery, this nozzle is a critical component for achieving superior atomization. By breaking the water-methanol mixture into a fine mist, it ensures rapid evaporation within the intake tract, which significantly lowers air charge temperatures and helps suppress engine detonation.

This 0.5 GPH flow rate is specifically suited for lower horsepower applications or as part of a staged, multi-nozzle configuration. The high-pressure design maintains a consistent spray pattern even under heavy load, providing the cooling and octane enhancement needed to protect your engine during high-boost or high-load operation.

• Manufacturer Part Number: SNO-N0050
• Flow Rate: 0.5 GPH (Gallons Per Hour)
• Designed for maximum fluid atomization and intake cooling
• Robust construction for reliable performance in high-pressure systems
• Compatible with standard water-methanol injection setups

Designed for high-horsepower applications that require precise tuning and engine safety, the Snow Performance SNO-94600H Direct Port Water-Methanol Upgrade provides individual cylinder injection for 6-cylinder engines. This hardline kit replaces single-nozzle plenum setups to ensure perfectly balanced fluid distribution across all six intake runners, preventing lean conditions in specific cylinders during high-boost operation.

This upgrade utilizes durable hardline plumbing for a permanent, professional-grade installation capable of handling high-pressure demands. The system includes a high-flow solenoid to prevent siphoning and ensure instantaneous fluid control. Note that this kit is designed for custom tuning; nozzles are not included and must be selected based on your specific horsepower requirements and engine displacement.

• Engineered for 6-cylinder engines requiring equalized port-to-port distribution
• Hardline plumbing provides superior durability and a clean aesthetic
• Includes 6-port distribution block and high-flow solenoid upgrade
• Allows for more aggressive ignition timing and higher boost levels
• Manufacturer Part Number: SNO-94600H
• Note: Injection nozzles are not included and must be purchased separately