· Vented to allow expansion and contraction of fluid while maintaining a tight seal

• · Vented to allow expansion and contraction of fluid while maintaining a tight seal
• · Ridged design to help prevent slipping when taking cap on and off
• · Direct replacement for either AEM 1.15 and 5-gallon reservoir
• · Wide cap for easy refills

Racers with high compression naturally aspirated engines or boosted engines who are looking for an alternative to boost-dependent water/methanol injection controllers have a solution in AEM's Multi-Input WMI controller. The multiple input design enables users to install AEM's Water/Methanol Injection Kit on both high compression naturally aspirated vehicles (NA) via the MAF/IDC settings and ultra-high boost vehicles (above 40 PSI) using an external MAP sensor. The Multi-Input controller works with an external 0-5v voltage-based external MAP sensor, a frequency-based input for Injector Duty Cycle (IDC), frequency-based mass airflow (MAF), or a 0-5v voltage-based MAF. The Multi-Input controller is offered in three kits; a one-gallon tank kit with a single injector for gas engines (PN 30-3350), a tank-less kit with a single injector (PN 30-3352), and a five-gallon tank kit with two injectors (PN 30-3351) for HD high-output gasoline applications.

• · Allows user to choose one of several signal inputs to control flow.
• · No reservoir allows integration of custom of 3rd party reservoir.
• · Optional wiring for W/M solenoid built into wiring harness
• · V3 nozzle included, enhanced atomization of W/M mixture

Water/methanol injection for forced induction (turbocharged or supercharged) gas-powered race engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows racers to reliably increase boost and advance ignition timing-without using high-octane racing fuel-for power gains of up to 20%. AEM's Water Injection Kits utilize robust hardware and deliver more advanced features than any other comparably priced water/methanol injection system.

• Terminated harness features positive lock connector with integrated pump ground circuit and additional wire for optional on/off flow solenoid
• One machined billet injector with integral check valve to prevent unintended flow
• Recirculation-style pump with integral fittings for quiet operation
• LED dash light for system status and low fluid warning
• Includes “Boost Safe” readiness failsafe system
• 20 ft. of high-pressure Nylon injection tubing

Boost Dependent and Multi-Input (0-5v/frequency) progressive controller designs feature large adjustment knobs, integrated plug for harness connection, integrated fuse, covered status light and test button for enhanced splash resistance and mounting tabs Wiring harness is terminated with a positive-lock connector on one end with color-coded wires to ease installation, integrated pump ground circuit and additional wire for optional on/off fluid solenoid "Boost Safe" failsafe output included (for complete failsafe under all conditions, see our Water/Methanol Failsafe Device) Heavy-duty high-pressure injection pump features integral fittings, a Santoprene diaphragm and EPDM seals to resist corrosion. Our pump maximizes line pressure for optimum atomization and its quiet, smooth operation is almost undetectable Precision-machined billet-aluminum injector with integral check valve Three interchangeable injector nozzles to cover a wide variety of HP levels (250cc/min, 500 cc/min & 1,000cc/min) 1.15-gallon tank with anti-starvation reservoir, integral conductive low-fluid sensor and positive lock connector (tank-less systems available) 20 feet of injection tubing included LED dash light for system status and low fluid warning

• Terminated harness features positive lock connector with integrated pump ground circuit and additional wire for optional on/off flow solenoid
• One machined billet injector with integral check valve to prevent unintended flow
• Recirculation-style pump with integral fittings for quiet operation
• LED dash light for system status and low fluid warning
• Includes "Boost Safe" readiness failsafe system
• 20 ft. of high-pressure Nylon injection tubing

The AEM Water/Methanol Solenoid is a 2-way, normally closed 12V valve with stainless steel body for use with AEM Water/Methanol Injection Systems. The shut-off valve provides an accurate and consistent shut off and prevents siphoning under vacuum.AEM offers performance automotive accessories to upgrade your existing water/methanol injection (WMI) system including inline water/methanol fluid filters, WMI flow gauges, the Water/Methanol Failsafe Device gauge, and water/methanol system nozzle and jet kits.30-3326 High-Flow Low-Current WMI Solenoid Prevents Unintended Flow

• The shut-off valve provides an accurate and consistent shut off and prevents siphoning under vacuum.
• Backwards compatible with AEM Water/Methanol Controllers
• Push lock fittings
• 2 wire connection

The new controller designs feature large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness's positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back. The Multi Input controller has an easy-to-remove plug covering the programming dipswitches and a programming legend on the back for the 0-5v and frequency based settings. Both controller housings feature an easy to access integrated fuse and molded mounting tabs.

• · Mounting hardware included to ease installation process
• · Compact design for various installation options
• · Built-in level sensor to warn of low level
• · Large reservoir cap to help with refill

Our breakthrough injector design uses unique Swirl Generator Technology that improves atomization to deliver faster inlet temp cooling and uses less fluid to maintain inlet air cooling. We include three Swirl Generators that deliver 250cc, 500cc, and 1000cc of flow.

• Unique Swirl Generator technology increases atomization for faster cooling.
• Faster cooling using unique Swirl Generator technology
• Interchangeable Pintle to inject between 250cc-1000cc
• Innovative design that increases atomization

-Can be used to add more length to existing system.

• -Can be used to add more length to existing system.
• -Nylon hose, black.
• -20ft hose length
• -¼” Diameter

Replacement V3 Water/Methanol Injectors (Qty 2), Includes Interchangeable Swirl Generators for 250cc, 500cc, & 1000cc of flow for each injector

• Includes Interchangeable Swirl Generators for 250cc, 500cc, & 1000cc of flow for each injector
• T-Adapter included to run dual nozzles
• Better Atomizing design
• Inject up to 2000cc

V2 Water/Methanol HD Controller Kit - Internal MAP with 40psi max, CONTROLLER ONLY

• -Barb fitting on the controller to connect boost line
• -Color coded harness for ease of installation.
• -System status LED on controller.
• -40PSI rated HD controller.

V2 Water/Methanol Multi Input Controller Kit- 0-5v/MAF Frequency or Voltage/Duty Cycle/Ext MAP, CONTROLLER ONLY

• -Color coded harness for ease of installation.
• -Can be used on NA and boosted applications.
• -Multiple triggers to activate system.
• -LED system status light

Water/methanol injection for forced induction (turbocharged or supercharged) gas-powered race engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows racers to reliably increase boost and advance ignition timing-without using high-octane racing fuel-for power gains of up to 20%. AEM's Water Injection Kits utilize robust hardware and deliver more advanced features than any other comparably priced water/methanol injection system.

• -Barb fitting on the controller to connect boost line
• -Comes with fitting for 3rd party tank.
• -Interchangeable nozzles.
• -LED system status light

The AEM Water/Methanol injection for forced induction (turbocharged or supercharged) Gas & Turbo Diesel applications is a proven means for effectively reducing engine inlet air temperatures and enhancing combustion efficiency whilst suppressing harmful detonation. This allows for reliable increase in boost and advance timing to deliver more power with less effort. AEM's Water/Methanol Injection Kits utilize robust hardware and deliver more advanced features than any other comparably priced Water/Methanol injection system.

• Multi-Input Controller allows for preference of connection for triggering
• Can be used on N/A or Forced Induction Applications.
• Kit is universal for installation/application
• Increases horsepower and torque

These new controllers retain the "Boost Safe" injection failsafe system, which is an output that will activate if there is a short, loss of continuity or high or low voltage or low fluid condition, allowing users to define their failsafe strategy from something as simple as flashing a warning light to more advanced strategies like pulling boost or ignition, or switching fuel maps on a standalone engine management system.Simplified WiringThe new wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. An integrated Pump Ground circuit is included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.Improved Injector Flow Rate & Nozzle SizesAEM's engineers spent extensive time revamping the controller's flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine's need for water/methanol injection, which further optimizes charge air cooling and detonation control. Three resized injector nozzles are in each kit and allow for improved flow capability (a flow graph is available on our website).New Low Level Fluid IndicatorA more accurate, conductive low level fluid sensor is integrated into the tank and features a positive lock connector with color-matched wires to the wiring harness. The sensor eliminates any chance of incorrect readings due to interference from debris.

• Terminated harness features positive lock connector with integrated pump ground circuit and additional wire for optional on/off flow solenoid
• Three interchangeable injector nozzles to cover a wide variety of HP levels (250cc/min, 500 cc/min & 1,000cc/min)
• 30-3350 Multi Input kit for high compression naturally aspirated and forced induction applications
• 30-3300 Boost Dependent kit (up to 35PSI) includes molded-in nipple for boost hose
• One machined billet injector with integral check valve to prevent unintended flow
• Recirculation-style pump with integral fittings for quiet operation
• Covered status LED and test button for improved splash resistance
• Integrated plug for mating to positive-lock connector on harness
• 1-gallon tank with built-in conductive low fluid level indicator
• Large adjustment knobs and numbering for easy programming
• LED dash light for system status and low fluid warning
• Includes "Boost Safe" readiness failsafe system
• 20 ft. of high-pressure nylon injection tubing
• Integrated fuse and mounting tabs
• CONTROLLER FEATURES:

Water/Methanol Injection 200psi Recirculation Pump w/ 3/8 -inch NPT Fittings

• 3/8 NPT Port for custom Hard/Braided Line
• Flows 1 Gallon per minute
• Directional flow
• up to 200 PSI

If part of your existing AEM Water/Methanol Injection system has become damaged, we offer all of the component parts individually, including our 200 PSI water/methanol injection pump, a WMI check valve kit, water/methanol injection tubing, 1.15- and five-gallon water/methanol fluid tanks and our conductive low fluid level sensor.

• Integrated push-lock hose connection
• Integrated bracket for easy mounting
• Sealed and weatherproofed unit
• High-Flow in a compact package

The AEM Water Injection Kit is a safe and economical way to reduce air inlet temperatures to increase boost pressure for more power. Lower air inlet temperatures allow users to advance timing without having to run higher-octane fuel. This is the most complete kit available on the market straight out of the box- no additional parts required.*STANDARD WATER INJECTION KIT* * Universal kit includes everything you need for installation * Progressive, controller-driven 150 PSI pump * One-gallon t

• -Installed on low pressure side of system (between tank and pump).
• -Protects the system from foreign particles.
• -Comes with 1/4" push lock fittings.
• -Filters up to 40 microns.

This Part Fits: