Fits select 2016-2026 Acura Integra and Honda Accord, Civic, CR-V, HR-V, and Insight.

The Whiteline KTA260 is a heavy-duty adjustable rear lower control arm kit engineered to provide an increased range of toe adjustment. This kit is essential for rectifying uneven tire wear on lowered vehicles or fine-tuning handling characteristics to reduce inherent understeer or oversteer behavior. Featuring a left-right-hand thread turnbuckle design, it allows for precise on-car alignment without removing the arms from the vehicle.

Constructed from premium anodized alloy, these arms provide a long-lasting barrier against corrosion and wear. The low-compliance synthetic elastomer bushings are formulated to resist oil, grease, and ozone while minimizing arm movement to improve suspension response without excessive noise, vibration, or harshness (NVH).

• Manufacturer Part Number: KTA260
• Increased toe adjustment range for performance alignment and tire wear correction
• On-car adjustment via left-right-hand thread turnbuckle nut
• Low-compliance synthetic elastomer bushings for reduced deflection and optimized strength
• Anodized alloy construction for superior corrosion resistance
• Articulation voids designed for necessary suspension compression under load
• 3-year / 60,000-mile manufacturer warranty

Fits select 2008-2026 Subaru (BRZ, WRX, STI, Crosstrek, Forester, Impreza, Legacy, Outback), Toyota 86/GR86, and Scion FR-S.

Whiteline heavy-duty adjustable rear lower control arms provide essential on-car adjustability to correct camber alignment. This is critical for vehicles with lowered suspension heights where factory adjustment is insufficient. By optimizing the tire contact patch, these arms improve traction, increase cornering grip, and prevent premature tire wear. Each arm is finished with a protective powder coating that acts as a durable skin, outlasting conventional paint and resisting corrosion in harsh environments.

• Camber Correction: +/- 3.5 degrees of on-car adjustment
• Design: Engineered to compensate for body roll, body distortion, and tire roll during high-load cornering
• Durability: Heavy-duty construction with corrosion-resistant powder coating
• Installation: Direct replacement for OE rear lower control arms
• Manufacturer Part Number: KTA139A
• Note: Recommended for motorsport use only

Fits 2013-2020 Subaru BRZ, Scion FR-S, and Toyota 86.

Restore steering precision and eliminate suspension slop with Whiteline front sway bar mount bushings. These 22mm bushings are engineered from a proprietary synthetic elastomer that provides the stiffness needed for performance driving without the harshness of traditional poly. This advanced material formulation is specifically designed to resist degradation from oil, grease, ozone, and extreme weathering, ensuring a much longer service life than factory rubber.

Designed as a direct replacement for the OE mount bushings, this kit allows the sway bar to operate more effectively by reducing deflection under lateral loads. The design facilitates a straightforward installation using standard tools, making it an essential upgrade for both daily drivers and track-focused ZN6/ZC6 platforms.

• Bore Diameter: 22mm
• Material: Synthetic Elastomer
• Resistant to oil, grease, and ozone
• Installation guide with detailed instructions included
• Manufacturer Part Number: KSK105-22

Fits select 2008-2015 Subaru Forester, Impreza, WRX, Legacy, and XV Crosstrek.

The Whiteline KSK001-20 Sway Bar Mount Bushing Service Kit is engineered to maintain the performance and responsiveness of your aftermarket suspension. Specifically designed as a service replacement for Whiteline sway bar kits BSR49 and BSR49Z, these 20mm bushings ensure your sway bar remains securely mounted for consistent roll control.

Constructed from a proprietary synthetic elastomer formulation, these bushings are highly resistant to oil, grease, ozone, and environmental weathering, preventing the degradation commonly found in factory rubber components. The internal bore features integrated grease reservoirs that provide continual self-lubrication, reducing friction and eliminating common suspension squeaks.

• Precision engineered for 20mm sway bars (Fits Whiteline BSR49 and BSR49Z)
• Synthetic elastomer construction for superior durability and chemical resistance
• Internal grease reservoirs for long-term lubrication and friction management
• Direct service replacement for worn or contaminated mount bushings
• Includes detailed installation guide for proper setup
• Manufacturer Part Number: KSK001-20

Fits select 1990-2007 Subaru Impreza (WRX/STI/RS), Forester, Legacy, and Saab 9-2X models. These Whiteline KLC26 rear sway bar links are engineered to eliminate the flex associated with original equipment plastic or thin-gauge steel links, providing more direct and precise roll control.

Constructed from high-tensile extruded alloy, this kit features ultra-low compliance synthetic elastomer bushings that allow for maximum sway bar articulation without the binding found in inferior components. By reducing deflection, these links allow for up to a 25% more effective bar rate available earlier in the suspension travel, resulting in sharper turn-in and increased responsiveness during lane changes. All metal components feature protective plating or powder coating to resist corrosion in harsh undercar environments.

• Manufacturer Part Number: KLC26
• Body Material: High-tensile extruded aluminum alloy
• Bushing Material: Synthetic elastomer for low compliance and high durability
• Finish: Protective plating and powder coating for superior corrosion resistance
• Hardware: Includes high-tensile mounting bolts and hardware
• Included: Extreme pressure molybdenum disulphide (LM) based grease for bushing lubrication
• Design: Standard length to maintain correct sway bar geometry and full suspension travel

Fits select 2017-2022 Hyundai Elantra, Elantra GT, Kona, Veloster, and Veloster N models.

The Whiteline KLC221 Rear Sway Bar Link Kit is designed to overcome the limitations of factory-style links, which often flex or suffer from preload under load. These high-strength adjustable links are engineered to deliver maximum sway bar effectiveness by providing a rigid connection between the sway bar and the suspension. By eliminating flex, these links improve steering responsiveness and chassis rigidity, specifically during high-speed lane changes and initial turn-in.

Manufactured from premium anodized alloy, the link bodies feature protective plating that acts as a durable barrier against corrosion and road debris. The heavy-duty steel ball joints are built for longevity and steering predictability. With on-car length adjustment and the ability to rotate to any angular combination, these links allow for precise tuning to eliminate sway bar preload, which is essential for maintaining neutral handling on lowered or performance-aligned vehicles.

• Materials: High-quality anodized alloy link bodies with heavy-duty steel ball joints.
• Adjustment: On-car adjustable length to eliminate sway bar preload.
• Durability: Protective plating resists corrosion in harsh conditions.
• Installation: Includes all necessary hardware and a detailed install guide for a direct-fit replacement.
• MPN: KLC221

Fits 2003-2025 Nissan 350Z, 370Z, and Z, and 2003-2015 Infiniti G35, G37, and Q60.

The Whiteline Motorsports Rear Differential Bushing Kit (KDT911M) is engineered to replace soft, high-compliance factory rubber bushings that allow for excessive differential movement under load. By securing the differential more rigidly to the subframe, this kit maintains critical pinion angles during hard acceleration and cornering. This results in more direct power transfer to the wheels, significantly reduced initial torque loss, and a more positive, mechanical feel during gear shifts.

As the Motorsports Version, this kit utilizes stiffer materials designed for maximum stability and consistent handling performance in high-load environments. It is an essential upgrade for track-oriented builds or high-performance street vehicles looking to eliminate the "clunking" and wheel hop often associated with worn or soft OE differential mounts.

• Maintains proper pinion angle for improved drivetrain efficiency and longevity
• Reduces drivetrain slop for better power delivery and throttle response
• High-quality synthetic elastomer resists wear and environmental degradation
• Kit includes: 5 Bushings and 2 Installation Tubes
• Manufacturer Part Number: KDT911M

Fits select 2004-2025 Subaru Forester, Impreza, Legacy, Outback, WRX, STI, and XV Crosstrek.

The Whiteline Positive Shift Kit (KDT901) is engineered to eliminate the vague, "mushy" feel of the factory gearbox by reducing the compliance of the heavily voided original mount. These synthetic elastomer inserts fit directly into the factory mounting points, providing a firmer connection that results in significantly improved shift response and tactile feedback during gear changes.

• Advanced synthetic elastomer formulation resists oil, grease, ozone, and atmospheric weathering.
• Internal grease reservoirs provide continuous self-lubrication for consistent friction management and quiet operation.
• Specially bonded design optimized for high-load applications and long-term durability.
• Supplied with extreme pressure molybdenum disulphide (LM) based grease to extend component life.
• Straightforward installation into the factory gearbox mount; detailed instructions included.
• Manufacturer Part Number: KDT901

Fits 2000-2005 Toyota MR2 Spyder Base.

The Whiteline BTR84Z is an 18mm heavy-duty rear sway bar engineered to reduce body roll and improve lateral load distribution. By minimizing sway during cornering, this bar spreads lateral loads more evenly across the tires, increasing mechanical grip and improving overall vehicle balance. The 4-point adjustable design allows drivers to fine-tune handling characteristics to suit specific driving conditions or performance preferences.

Built for durability and performance, the sway bar features a protective powder coating to resist corrosion and includes DIY lateral locks to prevent shifting under cornering loads. The kit utilizes Whiteline’s synthetic elastomer bushings, featuring internal bore knurling and grease retention lips for optimum lubrication and friction management.

• 18mm heavy-duty solid spring steel construction
• 4-point adjustability for precise handling tuning
• Synthetic elastomer bushings resistant to oil, grease, ozone, and weathering
• Internal grease reservoirs for self-lubrication
• Includes lateral locks, molybdenum disulphide (LM) based grease, and installation guide
• Manufacturer Part Number: BTR84Z

Fits 2018-2025 Subaru Crosstrek and 2019-2025 Subaru Forester (all trims including Hybrid and Wilderness).

Whiteline's 20mm 2-point adjustable rear sway bar is engineered to reduce body roll and improve lateral load distribution across the rear tires. By increasing the vehicle's roll stiffness, this bar enhances cornering grip and steering response without negatively affecting ride quality. The 2-point adjustment allows drivers to fine-tune the handling characteristics to suit specific driving conditions or personal preference.

Constructed from high-quality materials and finished with a protective powder coating, this sway bar is built to withstand harsh environments and resist corrosion. The kit features Whiteline's latest synthetic elastomer bushings, designed with internal bore knurling and grease retention lips for consistent lubrication and quiet, maintenance-free operation.

• Part Number: BSR56Z
• Diameter: 20mm
• Adjustment: 2-Point Adjustable
• Material: Solid spring steel with protective powder coat
• Bushings: Synthetic elastomer with grease-retention technology
• Kit Includes: (1) Rear Sway Bar and (2) Bushings

Fits select 2008-2021 Subaru Forester, Impreza, Legacy, Outback, WRX, STI, and XV Crosstrek.

The Whiteline BSR49Z rear sway bar is engineered to reduce body roll and neutralize understeer by distributing lateral loads more evenly across all four tires. This 20mm heavy-duty bar features a 3-point adjustable design, allowing you to fine-tune your vehicle's handling characteristics for daily driving or performance conditions without compromising ride quality. Constructed with forged ends for maximum strength at the link mounting points, this bar is finished in a protective powder coating to resist corrosion in harsh environments.

• Diameter: 20mm heavy-duty solid spring steel
• Adjustment: 3-point multi-position for fine-tuning roll stiffness
• Bushings: Synthetic elastomer with internal bore knurling and grease retention lips for superior lubrication
• Lateral Locks: Included DIY lateral locks prevent sideways movement under cornering loads
• Hardware: Includes high-quality mounting bushings and installation guide
• Finish: Premium protective plating and powder coating for long-term durability
• MPN: BSR49Z

Fits 2008-2015 Mitsubishi Lancer Evolution (GSR, MR, MR Touring, SE, and Final Edition).

The Whiteline BMK010 Sway Bar Kit is a complete handling solution designed to reduce body roll, improve turn-in response, and maximize mechanical grip. This engineered kit replaces the factory sway bars with high-diameter 27mm bars, featuring 3-point adjustability on both the front and rear. This allows drivers to fine-tune the vehicle's balance and roll stiffness to suit specific track conditions or street driving preferences.

Each kit includes heavy-duty adjustable sway bar links featuring steel ball joint ends, allowing for up to 25mm of on-car length adjustment to eliminate sway bar preload. The included bushings utilize Whiteline's synthetic elastomer formulation with internal bore knurling and grease retention lips for consistent lubrication. Forged ends ensure maximum structural integrity at the mounting points, while the DIY lateral locks prevent sideways bar movement under heavy cornering loads.

• Front Sway Bar: 27mm diameter, 3-point adjustable
• Rear Sway Bar: 27mm diameter, 3-point adjustable
• Bushings: Synthetic elastomer with PTFE lining to eliminate the need for lubrication
• Finish: Multi-stage protective E-Coat and powder coating for superior corrosion resistance
• Hardware: Includes heavy-duty adjustable links, lateral locks, and mounting accessories
• Manufacturer Part Number: BMK010

Fits 2006-2015 Mazda MX-5 Miata across all trims including Sport, SV, Touring, Club, and Grand Touring.

The Whiteline BMK004 sway bar kit is a comprehensive suspension upgrade engineered to reduce body roll and maximize mechanical grip. This engineered solution replaces the flexible factory bars with a 24mm 2-point adjustable front sway bar and a 16mm 3-point adjustable rear sway bar. By increasing roll stiffness and allowing for precise chassis tuning, this kit improves steering response and lateral stability during spirited driving and cornering maneuvers.

• Precision Tuning: Multiple adjustment points on both bars allow you to fine-tune the balance of your vehicle for oversteer or understeer characteristics.
• Advanced Material Science: Includes synthetic elastomer bushings with internal bore knurling and grease retention lips for consistent lubrication and quiet operation.
• Lateral Stability: DIY lateral locks are included to prevent sideways movement of the sway bar under heavy cornering loads.
• Enhanced Durability: All metal components feature protective plating and powder coating for superior corrosion resistance and longevity.
• Adjustable Links: High-strength links allow for up to 25mm of on-car length adjustment to eliminate sway bar preload.

Specifications:

• Part Number: BMK004
• Front Sway Bar: 24mm (2-Point Adjustable)
• Rear Sway Bar: 16mm (3-Point Adjustable)
• Construction: Forged ends for maximum strength at mounting points
• Hardware Included: Adjustable links, heavy-duty ball joints, and molybdenum disulphide (LM) grease

Fits select 1996-2005 Honda Civic models, including CX, DX, EX, GX, HX, Hybrid, LX, Si, and Value Package. This Whiteline 22mm 2-point adjustable rear sway bar is engineered to reduce body roll and improve cornering grip by spreading lateral loads more evenly across the tires during spirited driving or track use.

Constructed from high-strength steel and finished with a protective plating and powder coating, this sway bar is built to withstand harsh environmental conditions while resisting corrosion. The kit features Whiteline's latest synthetic elastomer bushings with a PTFE lining, providing a low-friction, maintenance-free surface that eliminates the need for periodic lubrication. Included DIY lateral locks prevent the bar from shifting sideways under heavy cornering loads, ensuring consistent suspension geometry.

• Part Number: BHR83XZ
• Diameter: 22mm solid steel construction
• Adjustment: 2-point multi-point adjustment for fine-tuning handling balance
• Bushings: PTFE-lined synthetic elastomer for quiet, grease-free operation
• Hardware: Includes lateral locks and high-strength link bushings
• Finish: Corrosion-resistant plating and durable powder coat

Fits select 2008-2017 Pontiac G8 and Chevrolet SS. The Whiteline BHK007 Front and Rear Sway Bar Kit is a complete suspension tuning solution designed to significantly reduce body roll and improve cornering grip. This kit replaces the compliant factory bars with high-diameter, adjustable units that allow you to fine-tune the handling balance of your vehicle for specific driving conditions or track layouts.

• Front Sway Bar: 26mm 4-point adjustable bar for precise front-end roll control.
• Rear Sway Bar: 22mm 3-point adjustable bar to manage oversteer and understeer characteristics.
• Adjustable End Links: Heavy-duty alloy links with steel ball joints, allowing for up to 25mm of length adjustment to eliminate sway bar preload.
• Synthetic Elastomer Bushings: Features internal bore knurling and grease retention lips for long-term lubrication and quiet operation.
• Lateral Locks: DIY lateral locks prevent the bar from shifting sideways under heavy cornering loads.
• Durable Construction: Forged ends for maximum strength at mounting points with protective powder coating and plating for superior corrosion resistance.

Each kit includes all necessary mounting accessories, high-performance molybdenum disulphide (LM) grease, and a detailed installation guide to ensure a straightforward bolt-on upgrade using factory mounting points.

Fits select 1963-1982 Chevrolet, Oldsmobile, Pontiac, and Omega models including Corvette, Camaro, Chevelle, Firebird, and Cutlass.

Protect your critical suspension components with Whiteline ball joint dust boots. These boots are designed to replace worn or cracked original equipment (OE) boots, preventing grease contamination and premature joint wear. Engineered for the installer, these components allow for easy fitment without the need for specialized shop tools or equipment.

• Precision-molded to seal out road grime, dust, and moisture
• Advanced formulation resists degradation from oil, grease, and weathering
• High ozone resistance prevents premature cracking and failure
• Direct-fit replacement for various vintage GM applications
• Manufacturer Part Number: W93460

Fits select 2005-2026 Nissan Frontier, 2005-2012 Pathfinder, 2005-2015 Xterra, and 2009-2012 Suzuki Equator.

Worn front control arm bushings significantly degrade vehicle stability, steering precision, and braking efficiency. The Whiteline Plus Front Lower Inner Control Arm Bushing Kit (W53272) replaces soft or failed OE components with advanced synthetic elastomer bushings. Engineered for durability, these bushings maintain superior elasticity and memory under high load, ensuring your suspension geometry remains consistent during heavy braking and cornering.

• Advanced Materials: Synthetic elastomer formulation resists oil, grease, ozone, and weathering for a significantly longer service life than rubber.
• Friction Management: Internal grease reservoirs provide continuous self-lubrication; includes molybdenum disulphide (LM) grease for extended maintenance intervals.
• Corrosion Resistance: Metal components feature protective plating and powder coating tougher than conventional paint to withstand harsh undercar environments.
• Bonded Design: Engineered for optimized strength in high load-bearing applications typical of truck and SUV front suspensions.
• Manufacturer Part Number: W53272

Fits 1992-1999 BMW 318i, 318is, 318ti, 323i, 323is, 325i, 325is, 328i, and 328is models.

Restore steering precision and sway bar efficiency with the Whiteline 27mm Front Sway Bar Mount Bushing Kit. Over time, original equipment rubber bushings soften and perish, leading to play in the suspension and reduced handling performance. These Whiteline bushings are engineered as a direct replacement to provide a more consistent connection between the sway bar and the chassis.

Constructed using advanced material formulation technology, these bushings are designed to withstand the harsh environment of the undercar. They offer superior resistance to oil, grease, ozone, and general weathering, ensuring a much longer service life than standard rubber components. The kit is designed for a straightforward installation, reducing the need for specialized shop tools or equipment.

• Bore Diameter: 27mm
• Advanced synthetic elastomer formulation for durability
• High resistance to oil, grease, and ozone
• Includes detailed installation guide
• Manufacturer Part Number: KSK034-27

Fits 2013-2018 Ford Focus ST.

The Whiteline KLC275 Adjustable Sway Bar Link Kit is a precision-engineered suspension solution designed to eliminate sway bar preload and optimize roll center geometry. These links are essential for vehicles with lowered ride heights or aftermarket adjustable sway bars, allowing for exact length adjustment to ensure the sway bar operates at its most effective angle.

Constructed from high-tensile steel with corrosion-resistant finishes, these heavy-duty links replace the flexible, non-adjustable factory units. By neutralizing the tension across the axle, this kit restores steering precision and reduces body roll for more consistent handling characteristics during aggressive cornering. This kit provides a complete vehicle solution by including both front and rear adjustable links.

• Heavy-duty adjustable design to neutralize sway bar preload
• High-tensile steel construction for maximum rigidity and durability
• Corrosion-resistant coating for long-term performance
• Includes front and rear links for a full vehicle upgrade
• Direct replacement for OE links to improve suspension geometry
• Manufacturer Part Number: KLC275

Fits select 1993-2025 Subaru Impreza, WRX, WRX STI, and Forester models.

Whiteline KLC262 adjustable sway bar links are engineered to eliminate sway bar preload and optimize suspension geometry. When a vehicle is lowered or fitted with upgraded sway bars, factory links can force the bar into an improper angle, leading to suspension bind or uneven handling. These front and rear adjustable links allow you to fine-tune the bar's position for neutral weighting, resulting in sharper steering response and reduced body roll during cornering.

Built from high-strength, corrosion-resistant materials, this kit is designed for lasting performance in both street and track environments. By replacing worn or flexible OE bushings with these rigid adjustable units, you unlock more precision from your chassis while ensuring compatibility with both factory and aftermarket suspension setups.

• Manufacturer Part Number: KLC262
• Adjustable design allows for precise sway bar geometry alignment
• Eliminates sway bar preload for predictable handling and balanced cornering
• Heavy-duty construction for improved rigidity over factory links
• Corrosion-resistant finish for long-term durability in harsh environments
• Includes all necessary mounting hardware for installation

Fits 2003-2008 Mitsubishi Lancer Evolution (including GSR, MR, RS, and SE).

The Whiteline BMK009 sway bar kit is a comprehensive handling upgrade designed to reduce body roll and increase mechanical grip. This engineered package replaces the flexible factory components with a heavy-duty 26mm solid front sway bar and a 24mm 3-point adjustable rear sway bar. By increasing the roll stiffness of the chassis, this kit provides flatter cornering, sharper turn-in response, and more predictable handling during rapid direction changes.

This kit includes Whiteline’s signature synthetic elastomer bushings, featuring internal bore knurling and grease retention lips for consistent lubrication. The rear bar offers three adjustment points, allowing you to fine-tune the vehicle's oversteer/understeer bias to suit your driving style. High-strength adjustable end links are provided to eliminate sway bar preload and maintain proper geometry on lowered vehicles.

• Manufacturer Part Number: BMK009
• Front Sway Bar: 26mm solid spring steel
• Rear Sway Bar: 24mm solid spring steel (3-point adjustable)
• Bushings: Synthetic elastomer with PTFE lining for low friction and zero maintenance
• Finish: Protective powder coating and E-coat for superior corrosion resistance
• Hardware: Includes heavy-duty adjustable end links, lateral locks, and mounting accessories
• Installation: Forged ends for maximum strength at mounting points; DIY-friendly lateral locks prevent bar shifting

Fits 2017-2023 Chevrolet Bolt EV and 2022-2023 Chevrolet Bolt EUV models.

The Whiteline BHR101 Rear Sway Bar is engineered to reduce body roll and improve the handling dynamics of your electric vehicle. By increasing the rear roll stiffness with a 22mm solid spring steel bar, lateral loads are distributed more evenly across all four tires during cornering. This results in increased grip, sharper turn-in response, and improved overall stability without significantly impacting ride quality or comfort.

This kit is a direct bolt-on upgrade designed for straightforward installation, helping to prevent the

The Whiteline WTK004 Wheel String Alignment Kit provides a professional-grade solution for setting precise vehicle alignment at the track or in the garage. This comprehensive system utilizes retractable string lines to establish a parallel reference frame, allowing for accurate toe measurements and suspension geometry tuning without a dedicated alignment rack.

Engineered for consistency and ease of use, the kit features durable components designed to withstand the rigors of trackside adjustments. The retractable string design ensures constant tension for repeatable measurements, while the included precision rulers allow for fine-tuning your setup. The entire system is housed in a rugged, hard plastic carry case for organized storage and easy transportation.

• Complete kit designed to simplify the wheel alignment and replacement process
• Retractable string lines provide a consistent, high-tension reference point
• Engineered components support repeatable performance and precision measurements
• Kit includes: 2 frames, 2 precision rulers, and 2 retractable strings
• Includes a hard plastic carry case for protection and portability
• Manufacturer Part Number: WTK004

The Whiteline Universal Press/Pull Tool Kit (WTK001) provides a safe, professional alternative to makeshift workshop methods for removing and installing suspension bushings. While using old bearing shells or sockets creates a significant safety risk because heat-treated steel can shatter under stress, these sleeves are engineered from mild steel to allow for distortion or crushing if over-pressed.

This comprehensive set is designed to simplify the installation and removal of Nolathane polyurethane bushings and assist with other general workshop pressing requirements. The kit features a wide range of sleeve sizes and heavy-duty threaded rods to ensure compatibility across various automotive applications.

• 18 Press tubes for various bushing diameters
• 4 Stepped plates for secure alignment
• 4 Threaded rods with 4 spare bearings
• 8 Spare bearing plates
• Mild steel construction for enhanced safety under load
• Manufacturer Part Number: WTK001

Fits 2020-2026 Toyota GR Supra models including Base, Premium, A91 Edition, and Launch Edition.

Whiteline Performance Lowering Springs deliver improved handling and a more aggressive stance while maintaining the safety and ride quality characteristics of your A90/A91 platform. By lowering the vehicle's center of gravity by 30mm, the unique progressive rate coil design reduces body roll and improves turn-in response. Developed and manufactured in Europe to strict tolerances, these springs are engineered for an exact fit and are compatible with both OEM and aftermarket shock absorbers.

• Manufacturer Part Number: WSK-TOY001
• Front Drop Height: 30mm
• Rear Drop Height: 30mm
• Front Spring Rate: 2.9 kg/mm (162 lb/in)
• Rear Spring Rate: 3.6 kg/mm (201 lb/in)
• Quantity: Set of 4 springs
• Design: Progressive rate coils for performance and comfort
• Origin: Manufactured in Europe

Fits 2022-2025 Subaru WRX (Base, GT, Limited, Premium).

Whiteline WSK-SUB009 Performance Lowering Springs are engineered to enhance the handling and aesthetics of the VB-chassis WRX while maintaining daily-driven ride quality. By lowering the vehicle’s center of gravity by 25mm, these springs reduce body roll and improve stability through corners. The unique progressive rate coil design ensures the suspension remains compliant over minor road imperfections while firming up under load for spirited driving performance.

Developed and tested in-house at Whiteline’s Australian facilities, these springs are cold-rolled from high-quality materials to exacting tolerances to ensure a perfect fit. They are specifically tuned to balance with both OEM and performance aftermarket shock absorbers, making them an ideal foundation for a complete suspension overhaul.

• Front Spring Rate: 4.5kg/mm (253lb/in)
• Rear Spring Rate: 5.3kg/mm (300lb/in)
• Target Drop: 25mm (Front and Rear)
• Design: Progressive rate coils for optimal performance and comfort
• Construction: Cold-rolled high-quality steel
• Included: Set of 4 springs (front and rear)
• Part Number: WSK-SUB009

Fits 2015-2021 Subaru WRX and 2015-2019 Subaru Legacy (2.5i / 3.6R).

Whiteline WSK-SUB008 Performance Lowering Springs are engineered to lower your vehicle's center of gravity, providing a 20mm drop that enhances both the aesthetic stance and cornering stability. These springs feature a progressive rate coil design, specifically tuned to improve handling response and reduce body roll without compromising the ride quality characteristics required for daily driving.

Cold-rolled in Europe from high-quality materials, these springs are manufactured to exacting tolerances to ensure a perfect fit with factory mounting points. They are designed to operate in optimal balance with both OEM and aftermarket shocks. For maximum corrosion resistance, the coils are finished with a tough, protective powder coating that withstands harsh road conditions.

• Front Spring Rate: 6.2kg/mm (347lb/in)
• Rear Spring Rate: 5.9kg/mm (333lb/in)
• Drop Height: 20mm Front / 20mm Rear
• Design: Progressive rate for performance and comfort
• Manufacturing: Cold-rolled in Europe
• Finish: Corrosion-resistant powder coating
• Part Number: WSK-SUB008

Fits 2015-2021 Subaru WRX STI (Base, Launch Edition, Limited, Series.HyperBlue, and Type RA).

Whiteline Performance Lowering Springs (WSK-SUB007) are engineered to improve vehicle handling and stance by lowering the center of gravity. These springs utilize a progressive rate coil design that maintains ride quality during daily driving while providing increased support during performance maneuvers. This kit delivers a consistent 15mm drop at both the front and rear, engineered to work harmoniously with either factory original equipment (OE) or aftermarket shock absorbers.

Manufactured in Europe, these springs are cold rolled from high-quality materials and finished with a durable powder coating that resists corrosion and harsh road conditions for long-term reliability.

• Front Spring Rate: 6.2kg/mm (347lb/in)
• Rear Spring Rate: 5.9kg/mm (333lb/in)
• Ride Height Drop: 15mm (Front) / 15mm (Rear)
• Progressive rate design for balanced performance and comfort
• Cold rolled construction for exact tolerances
• Protective powder coat finish for superior corrosion resistance
• Manufacturer Part Number: WSK-SUB007

Fits 2013-2020 Subaru BRZ, Toyota 86, and Scion FR-S.

Whiteline Performance Lowering Springs (WSK-SUB006) are engineered to drop your vehicle's center of gravity by 25mm, significantly reducing body roll and improving cornering performance while maintaining daily ride quality. These springs utilize a progressive rate coil design, ensuring a comfortable ride during normal cruising while providing the necessary stiffness under load for high-performance handling.

Developed and cold-rolled in Europe from premium materials, these springs are manufactured to the finest tolerances for a guaranteed exact fitment. The durable powder-coated finish acts as a protective skin, allowing the springs to withstand harsh road debris and resist corrosion. Whiteline engineers these coils to work in perfect balance with both OEM and high-performance aftermarket shock absorbers.

• Front Spring Rate: 3.1kg/mm (171lb/in)
• Rear Spring Rate: 4.2kg/mm (234lb/in)
• Approximate Drop: 25mm Front / 25mm Rear
• Progressive rate design for optimal balance of performance and comfort
• Cold-rolled European construction for superior material integrity
• Corrosion-resistant powder-coated finish
• Manufacturer Part Number: WSK-SUB006

Fits 2008-2014 Subaru Impreza and WRX models including Base, Limited, Premium, and Sport trims. This Whiteline performance spring kit is engineered to lower the vehicle's center of gravity for improved handling and a more aggressive stance without sacrificing street ride quality.

These springs utilize a unique progressive rate coil design that maintains comfort during daily driving but firms up under cornering loads to reduce body roll. Cold-rolled in Europe from high-quality materials and finished with a durable powder coating, these springs are designed to withstand harsh road conditions while resisting corrosion. They are engineered for optimal balance when paired with either OEM or aftermarket shock absorbers and are a direct replacement for factory units.

• Front Spring Rate: 5.0kg/mm (280lb/in)
• Rear Spring Rate: 3.8kg/mm (211lb/in)
• Ride Height Drop: 25mm (Approx. 1 inch) Front and Rear
• Construction: Cold-rolled progressive rate design
• Finish: Protective powder coating for corrosion resistance
• Manufacturing: Engineered and produced in Europe
• Manufacturer Part Number: WSK-SUB005