The DV8 Offroad Jeep Wrangler JK Rear Shock & Link Skid Plates provide bolt-on protection for the factory rear shock and link mounts. Their single-piece design reinforces the thin OE brackets and prevents damage from rocks and obstacles on the trail. These skids install easily, sit at the lowest point of the rear axle to help the Jeep slide over terrain, and work with most aftermarket shocks & lift kits. Piggyback shocks with fixed lower reservoirs are not compatible. Finished in a micro-texture black powder coat for durability.

• Places a skid plate on the lowest part of the rear axles for better off-roading capabilities. Won't get caught on rocks, and will slide right off.
• Shock and link mount skids are a single piece, unlike some competitors who tie the two mounts together for strength.
• Will work with most aftermarket shocks (Piggyback reservoirs that are locked on the bottom will not fit)
• Will work with lift kits and aftermarket links using Johnny Joints and Heim connections.
• Protects your links and shock mounts from smashing into rocks.
• 100% bolt-on application. Super easy install.
• Reinforces the thin factory shock mounts.
• Micro-Texture Black Powder Coat Finish

This Part Fits:

The MTO Series Rear Bumper for the Tundra features a mid-width design with a simple bolt-on installation. Two 3-inch light pods can be mounted behind aluminum accent panels for supplemental rear lighting. There are 2 clevis mounts that take ?-inch D-rings to provide recovery options if needed. Our design retains full functionality of the back-up sensors and the license plate light. There are inset mounting points for installing the OEM reverse lights. The MTO is compatible with the blind spot monitoring sensors, keeping the feature fully functional.

• Light mounting options for (2) 3" pods for additional lighting on the trail. (Behind Mesh)
• Optional Grip-Tape included for extra grip when bumper is wet or muddy.
• Retains the use of factory sensors and license plate/reverse lights.
• Contains paintable mesh inserts to accent the vehicle.
• Compatible with blind spot monitoring equipment
• Welded-in zip tie tabs for wire management.
• Bolt-on design (No cutting required)
• Sleek and tough Mid-width design.
• Provides (2) 3/4" D-ring Mounts.
• Factory Hitch Required

This Part Fits:

This DV8 Offroad Toyota Tundra rear bumper is designed to fit 07-13 Tundras. DV8 truck bumpers are made with high tensile strength 3/16 inch steel and reinforced with 1/4 inch steel in key areas which allows them to take a beating. Can accommodate up to a 12,500 lbs. winch. We also use a 2 step powder coating process which first coats the bumper with a thick layer of a proprietary compound for corrosion resistance. DV8 then coats the bumper with their textured black, UV resistant, scratch resistant powder coating. The result is a bumper that will look good and perform well for the lifetime of the vehicle. Details: Comes with D-Rings, Powdercoated, Easy installation, Accommodates Lights, Retains factory hitch receiver, Sold As: Each, Lights Not Included.

• Includes (2) 3" Round Led Lights
• Includes Side Step Cut Outs

This Part Fits:

Our MTO Series Tacoma Rear Bumper was designed as a direct replacement to the factory bumper, with no cutting or modification required for installation. It brings the addition of 2 reinforced clevis mounts that take 3/4-inch D-rings, providing you with recovery options. A 3-inch light pod can be mounted behind the aluminum mesh panels towards each end of the bumper. ?At each corner of the bumper is a side step, for convenience in accessing the truck bed. The MTO is compatible with factory rear parking sensors and retains full functionality. The blind spot detection module does not function with this bumper.

• Compatible With or Without Factory Hitch & Trailer Plug
• Side Steps at the Corners and Center of the Bumper?
• Side Steps at the Corners and Center of the Bumper
• Retains Factory Backup Sensors Functionality?
• Retains Factory Backup Sensors Functionality
• Installs to Factory Bumper Mounting Points?
• Retains OEM License Plate Mounts & Lights?
• Retains OEM License Plate Mounts & Lights
• Micro Texture Black Powder Coat Finish?
• Micro Texture Black Powder Coat Finish
• Light Mounts for Two 3" Light Pods?
• Light Mounts for Two 3 Light Pods
• Paintable Aluminum Mesh Panels?
• Paintable Aluminum Mesh Panels
• Two 3/4" D-Ring Mounts?
• Two D-Ring Mounts

This Part Fits:

This Made To Overland Series Rear Bumper was designed for heavy off-road use, and is compatible with our TCJL-13 Bumper Mounted MTO Tire Carrier (Available December 2023). The bumper features a full-width design with tapered wings compatible with factory or aftermarket fenders. The OEM spare tire mount can fit up to a 37-inch spare tire. The MTO retains use of the factory hitch & harness, and features sensor cutouts to retain full functionality of parking sensors. Two 3-inch light pods can be mounted behind the perforated aluminum accent panels. The bumper also has (2) 1-inch thick clevis mounts compatible with ?-inch D-ring shackles. A license plate bracket with an included light relocates your license plate away from the spare tire area to keep it visible when running a spare. On the interior of the bumper are welded zip-tie tabs for clean wire management. This features a fully bolt-on installation with no modifications required.

• Full Width Design that matches well with factory and aftermarket fenders
• Compatible with TCJL-13 bumper mounted tire carrier (to be released)
• Retains Factory Parking Sensors (recommend using MPRSNSR-01)
• Includes License Plate Relocation and License Plate Light
• Can Fit Up to a 37" Tall Tire With Factory Wheels/Mount
• Welded-in Zip Tie Tabs For Clean Wire Management
• Minor Wiring Required for License Plate Light
• Provides Mounts for (2) 3" Light Pods
• Compatible With Factory Hitch
• 1" Thick D-Ring Mounts

This Part Fits:

Our FS-7 Series Rear Bumper features a sleek, mid-width design. The FS-7 can fit up to a 37-inch spare tire above the bumper using the factory carrier. The bumper includes a license plate bracket with a license plate light to relocate the plate over to the side away from your spare tire. A pair of 1-inch thick reinforced mounts for D-ring shackles provide recovery options. Rear lighting options include (2) 3-inch pod light mounts that sit in a shielded position behind perforated aluminum accent panels. Welded zip tie tabs provide clean wire management.

• Can Fit Up to a 37 Tall Tire With Factory Wheels Using the Factory Spare Tire Mount.
• Works With Factory Rear Bumper Sensors (recommend using MPRSNSR-01)
• Includes License Plate Relocation and License Plate Light
• Provides (2) 1" thick D-ring mounts for 7/8 shackle pin.
• Welded-in Zip Tie Tabs For Clean Wire Management
• Provides mounting options for (2) 3 pod lights.
• Micro-Texture Black Powder Coat
• Compatible With Factory Hitch
• Sleek Mid-Width Design

This Part Fits:

Our FS-15 Rear Bumper features a low profile design suited for aggressive rock crawling. The bumper includes a license plate relocation bracket with a license plate light. The factory hitch and harness fit perfectly in an accessible position beneath the FS-15. For models equipped with factory sensors, we included sensor cutouts to retain full functionality of the feature. For models without factory sensors, we include sensor hole plugs for a clean look. Up to a 37-inch spare tire will fit on the OEM carrier above the bumper.

• Works with factory rear bumper sensors (recommend using MPRSNSR-01)
• Includes License Plate Relocation and License Plate Light
• Provides (2) 1" thick D-ring mounts for 7/8" shackle pin.
• High Clearance Design For Aggressive Rock Crawling
• Welded-in Zip Tie Tabs For Clean Wire Management
• Micro-Texture Black Powder Coat
• Compatible With Factory Hitch
• Direct Fit/ Bolt On Design
• Aluminum backed logo

This Part Fits:

Introducing the new Spec Series line of bumpers from DV8 Offroad. This high clearance Jeep Rear Bumper was designed for aggressive rock crawling. It was designed with an ultra-low profile that offers rear end protection and a multi-faceted, stylish look. Two clevis mounts that take D-ring shackles provide recovery options. Towards either end of the bumper are mounting points for a 3-inch light pod for supplemental trail lighting.

• Includes License Plate Relocation Bracket & Plate Light
• Accepts (2) 3" Pod Lights For Supplemental Lighting
• High Clearance Design For Aggressive Rock Crawling
• Welded-in Zip Tie Tabs For Clean Wire Management
• Micro-Texture Black Powder Coat Finish
• Retains Back-Up Sensor Functionality
• Clevis Mounts for D-Ring Shackles
• Direct Fit Bolt-On Installation
• Satin Black Accent Panel

This Part Fits:

The bumper works with single or dual-tip exhaust, supports 4- and 6-sensor models, and reuses factory license plate lights. It includes mounts for two 3" pod lights, welded zip tie tabs for wire management, a CNC-cut logo, and a durable micro-texture black powder coat finish.

• If the vehicle is equipped with backup sensors, we recommend purchasing DV8 Part # MPRSNSR-01 sensor bezels for ease of installation.
• Light mounting options for (2) 3" pods for rear facing lighting on the trail
• Full width design for protection and full coverage off-road
• Utilizes factory sensors and license plate lights
• Welded-in zip tie tabs for easy wire management
• Micro-Texture black powder coat finish
• Bolt-on design (No cutting required)
• Satin black aluminum accent plates
• Factory hitch compatible

This Part Fits:

The bumper includes mounting provisions for two 3" rear-facing pod lights and welded-in zip tie tabs for clean wire management. It remains fully compatible with the factory hitch, OEM parking sensors, license plate lights, and Blind Spot Monitoring systems. Block-off plates are included for vehicles not equipped with BSM.

• Blind Spot Monitoring compatible (block-off plates included if vehicle is not equipped)
• Light mounting options for (2) 3" pods for rear facing lighting on the trail
• Full width design for protection and full coverage off-road
• Utilizes factory sensors and license plate lights
• Welded-in zip tie tabs for easy wire management
• Micro-Texture black powder coat finish
• Bolt-on design (No cutting required)
• Satin black aluminum accent plates
• Factory hitch compatible

This Part Fits:

The bumper includes welded zip tie tabs for clean wire management, integrated mounts for two 3" pod lights, and reuses factory license plate lights for simple installation. Compatible with both single and dual exhaust models, the bumper can be installed with or without the included dual exhaust tip covers.

• Compatible with single or dual tip exhaust models (can be used with or without provided dual exhaust tip covers)
• Low profile, lightweight design that complements the factory look of the truck
• Welded-in Zip tie tabs for clean wire management
• Utilizes factory license plate lights & sensors
• Sleek prerunner tube based design
• Micro-texture black powder coat
• Compatible with factory hitch
• Direct fit/bolt-on design
• (2) 3" pod light mounts
• CNC logo on end caps

This Part Fits:

The sleek design and added satin black aluminum accent panels complements your rigs styling. Installation is easy due to the fully bolt-on design. The bumper is compatible with the OEM tire carrier up to a 37-inch spare. To retain full visibility of the third brake light with a 37-inch spare, purchase our Third Brake Light Extension Bracket. Our bumper allows you to retain full use of the factory hitch.

• Up to a 37 Spare Tire Will Fit Above the Bumper on the OEM Carrier
• Fully Bolt-On Design That Doesnt Require Modification or Drilling
• Features Welded-In Zip Tie Tabs for Clean Wire Management
• Features (2) 1 Thick D-Ring Mounts that Accept a 7/8 Pin
• Direct Fit that Enhances Factory Styling
• All Mounting Hardware is Included
• Compatible with All Trim Levels
• Micro-Texture Black Powder Coat
• Compatible with Factory Hitch
• Satin Black Accent Panel
• Mounts (2) 3 Light Pods
• Aluminum Backed Logo

This Part Fits:

DV8 Offroad?s 6th Gen Bronco Competition Series Rear Bumper is a steel tube & plate constructed low-profile bumper inspired by desert racing. Towards either side of the bumper are light mounts suited for 3-inch LED light pods. Its low-profile design allows you to fit up to a 37-inch spare tire. The OEM reverse sensors are integrated into the bumper via mounting holes, this retains full functionality of the feature. It also accommodates the factory hitch. There are two, paintable aluminum accent panels that help cut weight and add to the style of the bumper. Installation is a simple bolt-on process.

• Retains Full Functionality of OEM Backup Sensors
• Two Light Mounts that Fit 3 Light Pods
• Low-Profile Desert Racing Design
• Paintable Aluminum Accent Panels
• Tube & Plate Steel Construction
• Accommodates Factory Tow Hitch
• Fits up to a 37 Spare Tire
• Bolt-On Installation

This Part Fits:

The DV8 Offroad LBUN-01 is a bolt-on bull bar with light mount for MTO Series Front Bumpers. Manufactured from high grade steel and protected with a powder coat finish, the LBUN-01 can mount the DV8 Offroad 13-Inch Elite Series Light Bar.

• ACCOMMODATES 13-INCH ELITE SERIES LIGHT BAR
• 2-STAGE MICRO-TEXTURE POWDER COAT

This Part Fits:

Bolt-on brush guard designed to work with the factory bumper and recovery points. Adds front-end protection against brush and light debris, and a rugged appearance while retaining full compatibility with all factory sensors and components. Accepts universal 2" tube light brackets and reuses factory hardware for an easy DIY installation. Finished in a durable micro-texture black powder coat.

• Works with all factory sensors and components without issue
• Adds an extra layer of brush protection while off-road
• Works with factory bumper & recovery points
• Accepts universal 2" tube light brackets
• Micro-Texture Black Powder Coat Finish
• Reuses Factory Hardware
• Provides a rugged look
• Easy DIY install

This Part Fits:

Our Capable Bull Bar is designed for the OEM Capable Front Bumper, and provides lighting options and light protection when off-road. A 13 to 20-inch dual or single row light bar can be mounted either on-top or below the bull bar for supplemental lighting in dark or dusty conditions. Alternatively, you can run 3-inch pod lights above the bar. Each lighting configuration is easily set up with adjustable and removable light tabs. The bull bar sits in front of your rigs grille guarding it from shrubs, branches, and other light debris. It is made from high-quality steel and finished in a micro-texture black powder coat that accents the Capable Front Bumpers factory design.

• Compatible w/ (1) 13-20 Dual or Single Row Light Bar
• Micro-Texture Black Powder Coat Finish
• Designed for the Capable Front Bumper
• 3mm & 3.5mm Steel Plate Construction
• Adjustable & Removable Light Tabs
• Compatible w/ 3 Pod Lights

This Part Fits:

After installing most off-road bumpers, the open ends of the crash bar are left exposed and unsightly. These steel crash bar caps provide a finished look to the bar, and offer a mounting point for accessories. The accessory mount can be used to install up to 3-inch light pods, rock lights, RGB accent lights, or even a GoPro camera.

• Accessory Mount for Light Pods, Rock Lights, or Action Camera
• Micro-Texture Black Powder Coat Finish
• Cleans up Unfinished Crash Bars
• Works with up to 35 Tires
• Bolt-On Installation

This Part Fits:

This DV8 bull bar was designed for use with the OEM modular steel front bumper, and it mounts to the factory accessory mount locations utilizing OEM hardware. It sits much lower in front of the grille than the OEM version, giving it a low profile stance. A 13-inch single row LED light bar can be mounted within the bull bar, keeping a streamlined appearance.

• Offers Grille Protection Against Light Obstacles
• Fits a 13-inch Single Row LED Light Bar
• Mounts to OEM Modular Front Bumper
• Direct Bolt-On Installation
• Utilizes Factory Hardware

This Part Fits:

The DV8 Jeep Wrangler JL LED Grille Lights give you the presence and visibility that you need while off-road. A single bracket positions the three high-powered LEDs perfectly spaced in your grille.We designed these lights to be recessed slightly to protect them from debris and the elements, but they remain in view from almost all angles. Whenever you pass through dust, snow, or rain, our Wrangler LED Grille Lights will ensure your Jeep willbe seen.

• THREE BIGHT AMBER LEDS WITH MOUNTS

This Part Fits:

The DV8 Offroad GRJL-01 Jeep JL & Gladiator Replacement Grille adds a menacing look to the front end of your ride. With the JL and Gladiator's larger 9-inch headlights, the angry eye look has never been so mean. This is easy to install, and utilizes factoring grille mounting points.

• Replaces OEM Grill
• Easy To Paint
• Easy Install

This Part Fits:

Our Centric Series Front Bumper has all the features you need in an off-road bumper, in a compact & low-profile package. It was designed to complement factory styling, avoid altering the fenders, and to provide lighting and multiple recovery options. There is a hidden winch mount capable of fitting multiple size winches. Winch access is provided above the bumper, just beneath the grille. Cutaways on either side of the fairlead provide mounting points for 3-inch light pods. If youre not running pods at these cutaways, they can be used as additional access points for the winch. Below the winch is an inset mounting point for a single row 20-inch light barAdditional recovery options are afforded by the 1-inch thick D-ring mounts that take -inch D-rings with -inch shackle pins.

• (2) Mounting Points for 3 Light Pods (Only When Not Running a Winch)
• Welded Tabs Provide Clean Wire Management Options
• Compatible with Adaptive Cruise & Parking Sensors
• Mounting Point for 20 Single Row Light Bar
• Compatible with All Factory Skid Plates
• 1 Thick D-Ring Mounts for Shackles
• Center Mount Factory Style Bumper
• Compatible with all Trim Levels
• Accepts Multiple Size Winches
• Hidden Winch Mount

This Part Fits:

The MTO Series bumper is compatible with factory skid plates across all trims, including the TRD. The Adaptive Cruise Control module is unaffected, retaining full functionality. The parking sensors are incorporated into the bumpers design and function normally. Additionally, the intercooler is guarded by steel plating for added protection. Steel tabs for zip ties at strategic locations on the interior of the bumper help you to achieve solid wiring management for your lights and winch.

• High Clearance Design for an Ultimate Approach Angle
• Compatible with Stock Skid Plates Including TRD
• Mounts for (2) 3 Light Pods & (1) 20 Light Bar
• Hidden Winch Mount for Many Sized Winches
• Internal Zip Tie Tabs for Wire Management
• Armor the Protects the Lower Intercooler
• Paintable Aluminum Accent Panels
• Retains ACC & Parking Sensors

This Part Fits:

Our Winch Front Bumper is made with 3, 3.5, and 5mm plate steel for a robust construction that is built to protect the front of your rig from obstacles. The bumper is finished in a durable micro-texture black powder coat to prevent rust and is also compatible with OEM sensors, cameras, fog lights, and adaptive cruise control. Installation is easy with minimal cutting required. The integrated zip tie tabs allow you to effectively organize your aftermarket lights wiring.

• Retains OEM Sensors, Fog Lights, Cameras, and Adaptive Cruise Control
• Accepts Various Standard Sized Heavy Duty Winches
• (2) 1 Thich D-Ring Mounts that Accept a 7/8 Pin
• Welded-In Zip Tie Tabs for Wire Management
• Micro-Texture Black Powder Coat Finish
• Made out of 3, 3.5, & 5mm Plate Steel
• Mounts (1) 20 Single Row Light Bar
• Minimal Cutting Required
• Mounts (2) 3 Pod Lights

This Part Fits:

We designed the Centric Series Winch Front Bumper for durability and to match factory styling. This center mount bumper doesnt require cutting into the side fenders like a full-width bumper would require. A hidden winch mount can fit multiple size winches, and is tucked away behind the bumper skid. Additional recovery options are provided by 1-inch thick mounts that take -inch D-rings.

• Minimal Cutting for an Easy Installation
• Mounts a 20 Single Row LED Light Bar
• Center Mount Winch Front Bumper
• Micro-Texture Black Powder Coat
• 1 Thick D-Ring Shackle Mounts
• Accepts Multiple Size Winches
• Mounts (2) 3 LED Light Pods
• Complements Factory Styling

This Part Fits:

2016+ Toyota Tacoma Center Mount Winch Capable Front Bumper. The DV8 Offroad FBTT1-05 Tacoma Center Mount Bumper takes away the hassle of cutting your OEM plastic when installing an aftermarket bumper on a 16+ Tacoma and also allows you to mount up to a 12,500 lbs. winch. For those who want exceptional looks and function without committing to a full length bumper or cutting up a brand new truck. Details: Bolt on design, No cutting required, Excellent clearance, Mounts up to a 12,500 lbs. winch, Comes powder coated

• Micro-Texture Black Powder Coat Finish
• (1) 20 Light Bar Mount on Bull Bar
• Retains OEM Fog Lights & ACC
• 3mm/5mm Steel Construction
• (2) 1 Thick D-Ring Mounts
• Included Bolt-On Bull Bar
• Heavy-Duty Winch Mount
• Welded-In Zip Tie Tabs
• Center Mount Design

This Part Fits:

2024-2026 Toyota Land Cruiser Spec Series Front Bumper. Accepts multiple winch sizes (max 20.9” x 6.3” x 10”). Fits (2) 3” pod lights and a 20” light bar. Includes four top slots for hidden light mounting. Retains factory sensors and ACC. Hidden winch mount with 1” D-ring recovery points. Welded zip-tie tabs for wire management. Micro-texture black powder coat with satin black accent panel. Includes skid plate to front cross member. Fully bolt-on installation.

• Accepts Multiple Size Winches (Max dimensions: 20.9” x 6.3” x 10” Length x width x height)
• 4 elongated slots on top of bumper to mount lights behind factory bumper mesh
• Retains Factory Parking Sensors and ACC Locations
• Welded Zip-Tie Tabs for Clean Wire Management
• Skid plate from bumper to front cross member
• 20” Light Bar Mount in Center of Bumper
• (2) 3” Pod Light Mounts in Side Pods
• Micro-Texture Black Powder Coat Finish
• Satin Black Accent Panel Finish
• Improves Ground Clearance
• 1” Thick D-Ring Mounts
• Bolt-On Installation
• Hidden Winch Mount

This Part Fits:

The front bumper is finished in a micro-texture black powder coat. It retains the OEM front camera, sensors, fog lights, skid plate, and adaptive cruise control in equipped vehicles. Installation is straightforward, and included with the bumper are welded-in zip tie tabs. The bumper is compatible with all trim levels, including the 1958.

• Retains OEM Front Camera, Sensors, & ACC
• Micro-Texture Black Powder Coat Finish
• Retains OEM Fog Lights & Skid Plate
• (1) 20 Single Row Light Bar Mount
• Cutting Required for Installation
• 3/3.5/5mm Steel Construction
• (2) 1 Thick D-Ring Mounts
• Integrated Winch Mount
• Welded-In Zip Tie Tabs
• Center Mount Design

This Part Fits:

The 2025 Toyota 4Runner Centric Winch Front Bumper adds strength and off-road protection while keeping a factory look. It fits most winches, a 20-inch light bar, and two 3-inch light pods, with optional extra light mounts. It retains factory sensors and fog lights, includes welded zip-tie tabs for clean wiring, needs only minor cutting to install, and comes in a durable micro-texture black powder coat.

• Center mount design to keep factory styling while offering recovery and protection offroad.
• Rugged steel design complements the factory bumper and aesthetic.
• Optional light mounts for additional lighting on the trail.
• Keeps sensors and factory fog lights in stock locations.
• Minimal cutting makes for a quick and easy install.
• (2) 1" Thick D-Ring mounts that accept a 7/8" pin
• Welded-in zip tie tabs for wire management.
• Minor cutting Required for Installation
• Not Compatible with Factory Skid Plate
• Accepts a 20” Single Row Light Bar
• Micro Texture Black Powder Coat
• Accepts multiple size winches.
• Accepts Two 3” Light Pods

This Part Fits:

Our Centric Series Winch Front Bumper features a mid-width design that complements the iconic style of the front end. A hidden winch mount that accepts multiple size winches and 1-inch thick D-ring mounts provide ample recovery options. A recessed light mount for 20-inch single row light bars sits at the center of the bumper. Additional lighting provisions include (2) 3-inch pod light mounts. Note that if you install the pod lights, you will need a winch with a wireless remote as the pods will block access. Welded zip-tie tabs provide for clean wire management behind the bumper.

• (2) 3 Light Pod Mounts (Removes Access to Winch Unless it has Wireless Remote)
• Welded Zip Tie Tabs for Clean Wire Management
• Hidden Winch Mount for Multiple Size Winches
• Does not Interfere with Factory Fog Lights
• Micro-Texture Black Powder Coat Finish
• Mid-Width Center Mount Front Bumper
• Recessed 20 LED Light Bar Mount
• (2) 1 Thick D-Ring Mounts
• Retains Factory Styling

This Part Fits:

The Front Bumper features removable wings for a full or stubby width design. The bumper offers a recessed winch mount, and it is compatible with the OEM tow hooks in equipped vehicles. The bumper provides two light mounts that are compatible with (2) 3-inch pod lights or DV8’s JL & JT 4-inch LED Fog Lights. You can also install DV8’s Elite Series Light Bar Mount to the top of the bumper for running DV8’s 13-Inch Elite Series LED Single Row Light Bar. The included bull bar is removable, and the bumper comes with a winch plate cover for when you’re not mounting a winch. The bumper is made from steel, and it is finished in a micro-texture black powder coat. * Please Note: The bumper is not compatible with the factory front skid plate. As a replacement, we recommend DV8’s Sway Bar Disconnect Skid Plate. ** Please Note: Minor trimming may be required for installation. *** Please Note: The bull bar and winch may obstruct the front camera in equipped vehicles.

• Included Winch Plate Cover for when Winch Mount is Not Utilized
• Compatible w/ DV8’s 13” Elite Series Light Bar & Mount
• Compatible w/ Factory Jeep Tow Hooks (If Equipped)
• Removable Wings for a Full or Stubby Width Design
• (2) 4” Fog Light or 3” Pod Light Mounts
• Micro-Texture Black Powder Coated Finish
• 3mm & 5mm Steel Construction
• Included Steel Bull Bar
• Recessed Winch Mount
• Retains OEM Styling

This Part Fits: