These end links are also a little longer than recommended lengths to allow clearance for our Larger Diameter tie rod upgrade. Used as a Heavy-Duty replacement of the OE style end links which are notorious for breaking.Our Sway bar link kits utilize a lower clevis system which takes some of the angle off of the link when the suspension is cycling. Minimizing stress that can cause breakage.While we often upgrade other manufacturers kits with these links. We recommend you check your current length and match it up to the specs to help order the correct size if you do not have a Cognito Motorsports lift. Sold in pairs. Made in the USA.Note:Mounting surface to mounting surface measurement for this kit is 17 Inch (Measured from top of lower control arm up to the bottom of sway bar).

• Lower clevis system which takes some of the angle off of the link when the suspension is cycling minimizing stress that can cause breakage
• Front Front Sway Bar End Link Kit for 10-12 Inch lifts on 01-18 2500/3500 2WD/4WD / 99-06 Silverado/Sierra 1500 2WD/4WD
• Lift Height: 10-12 Inches
• Polyurethane bushings
• Made in the USA

This Part Fits:

These end links are also a little longer than recommended lengths to allow clearance for our Larger Diameter tie-rod upgrade. Used as a Heavy-Duty replacement of the OE style end links which are notorious for breaking.Our Sway bar link kits utilize a lower clevis system which takes some of the angle off of the link when the suspension is cycling. Minimizing stress that can cause breakage.While we often upgrade other manufacturers kits with these links. We recommend you check your current length and match it up to the specs to help order the correct size if you do not have a Cognito Motorsports lift. Sold in pairs. Made in the USA.Note:Mounting surface to mounting surface measurement for this kit is 14 Inch(Measured from top of lower control arm up to the bottom of sway bar).

• Lower clevis system which takes some of the angle off of the link when the suspension is cycling minimizing stress that can cause breakage
• Front Sway Bar End Link Kit for 7-9 Inch lifts on 01-19 Silverado/Sierra 2500/3500 2WD/4WD / 99-06 Silverado/Sierra 1500 4WD
• Lift Height: 7-9 Inches
• Polyurethane bushings
• Made in the USA

This Part Fits:

These end links are also a little longer than recommended lengths to allow clearance for our Larger Diameter tie-rod upgrade. Used as a Heavy-Duty replacement of the OE style end links which are notorious for breaking.Our Sway bar link kits utilize a lower clevis system which takes some of the angle off of the link when the suspension is cycling. Minimizing stress that can cause breakage.While we often upgrade other manufacturers kits with these links. We recommend you check your current length and match it up to the specs to help order the correct size if you do not have a Cognito Motorsports lift. Sold in pairs. Made in the USA.Notes:Mounting surface to mounting surface measurement for this kit is 11 Inches (Measured from top of lower control arm up to the bottom of sway bar).

• Lower clevis system which takes some of the angle off of the link when the suspension is cycling minimizing stress that can cause breakage
• Front Sway Bar End Link Kit for 4-6 Inch lifts on 01-19 2500/3500 2WD/4WD
• Lift Height: 4-6 Inches
• Polyurethane bushings
• Made in the USA

This Part Fits:

These end links are also a little longer than OE recommended lengths to allow clearance for our Larger Diameter tie-rod upgrade. Used as a Heavy-Duty replacement of the OE style end links which are notorious for breaking. Our Sway bar link kits utilize a lower clevis system which takes some of the angle off of the link when the suspension is cycling.Minimizing stress that can cause breakage. While we often upgrade other manufacturers kits with these links. We recommend you check your current length and match it up to the specs to help order the correct size if you do not have a Cognito Motorsports lift. Sold in pairs. Made in the USA.Notes:Not compatible with 2007 Classic body style models (2007 Classic style compatible with 99-06 model components).Mounting surface to mounting surface measurement for this kit is 7 Inch (Measured from top of lower control arm up to the bottom of sway bar).

• Lower clevis system which takes some of the angle off of the link when the suspension is cycling minimizing stress that can cause breakage
• Polyurethane bushings
• Made in the USA

This Part Fits:

Carli Machined Aluminum Sway bar End Links correct the geometry on Ram 1500s with 1-2" rear lifts.

• Machined aluminum bodies with forged ends, urethane bushings and stainless crush sleeves.
• Fits 2009-2023 Ram 1500 without factory air ride.
• Geometry is corrected on 1"-2" rear lift systems
• Includes grade 8 hardware.

This Part Fits:

Carli Sway Bar End Links for 2017+ Ford Super Duty trucks provide geometry correction on 2.5" leveled trucks and give the customer thhe option of upgrading to the full sway bar in the future.

• Greasable and fully rebuildable design allows for easy maintenance.
• Direct bolt-in design drastically improves sway bar articulation.
• Machined from 17-4 stainless steel.

This Part Fits:

Keep your rear sway bar within factory tolerances after installing a 1"-2" rear lift with the Carli extended rear sway bar links.

• Returns Rear Sway Bar to factory alignment with 1″-2″ rear lift.
• Forged Ends, Urethane Bushings, & Stainless Crush Sleeves.
• Machined aluminum construction with Grade 8 hardware.
• Fits 2014+ Ram 2500 4x4 and 2009-18 Ram 1500 4x4.

This Part Fits:

Carli Extended sway bar links are a strong and durable solution for correcting sway bar geometry when installing a 3" front lift.

• Machined from 17-4 stainless steel.
• Uses 1/2" FK chromoly rod end.
• Works with 0-3" of front lift.
• Grade 8 hardware

This Part Fits:

This Part Fits:

This Part Fits:

Due to the heavy demands put on the Dodge Ram 4WD pick-ups, one of those pesky maintenance items that are so often replaced a multiple-of-times could virtually now be replaced for the last time! The sway bar end links on the 2000-2009 4WD 2500/3500 (Diesel and HEMI) are prone to wearing or pounding out, and, even breaking when the truck is lifted on 2-post vehicle lifts due to the stress of the axle dropping. BD's Sway Bar End Links have a Dual Pivot Design that allows for greater amount of articulation and less stress. Long life Urethane bushing design allows for greater flex without breaking and will not pound out or seize due to the elements. Things that even the competition would be envious of. All components are designed to be easily serviceable and wearing items are low cost to replace. Kits come complete with all hardware and can quickly be installed in approximately 1-hour.

• Trucks lifted more than 3-inches will require sway bar offset spacer which is typically included in most lift kits
• Stock Units Can Even Break When Lifted On 2 Post Vehicle Lifts
• Stock units can even break when lifted on 2-post vehicle lifts
• Stock sway bar end links are prone to wearing or pounding out
• Could virtually be the last time they have to be replaced!
• Could Virtually Be The Last Time They Have To Be Replaced
• All Components Are Designed To Be Easily Serviceable
• Can Be Quickly Installed In Approximately 1 Hour
• Can quickly be installed in approximately 1-hour
• Will Not Pound Out Or Seize Due To The Elements
• Greater Amount Of Articulation And Less Stress
• Replacement bushing set available p/n 1312051
• Wearing Items Are Low Cost To Replace
• Long Life Urethane Bushing Design
• 12 Months or 24000 Mile Warranty
• Greater Flex Without Breaking
• Dual Pivot Design
• Gas & Diesel

This Part Fits:

This Part Fits:

This Part Fits:

Made with high quality Aurora rod ends and precision machined adjusters, these end links will make short work of dialing in your suspension. Joint articulation was designed to exceed factory range which prevents binding during operation. Equipped with right-hand and left-hand rod ends, the end links can be adjusted on-car without removal. Whether you’re setting up your car for the street or track, aFe Control will get you there! Our adjusters are CNC machined out of 6061-T6 aluminum and anodized blue with laser etched logo. For superior quality and reliability, we use PTFE lined Aurora rod ends.

• 6061-T6 Billet Aluminum Adjusters Anodized Blue with Laser Etched Logo
• Direct Fit Installation Requires No Modifications
• Front Adjustment Range: 14.875 IN - 16.125 IN
• Rear Adjustment Range: 4.375 IN – 5.625 IN
• PTFE Lined Aurora Rod Ends
• Proudly Made in the USA
• 1144 StressProof Studs

This Part Fits:

aFe Control PFADT Series Heavy Duty Street End Links Set; Chevrolet Corvette (C5/C6/C7) 97-15

• Upgrades Factory End Links To HD High Articulation Rod Ends
• Heavy Duty.5 in. PTFE Lined Rod Ends
• CNC Machined Articulation Spacers
• No Modifications Necessary
• Direct Fit Installation
• Incl. Grade 8 Hardware

This Part Fits: