This Part Fits:

This Part Fits:

This Part Fits:

The Snow Performance High Flow Solenoid offers 100% safety for all injection systems utilizing rear mounted reservoirs, injection points under vacuum, or installs where the injection nozzle is lower than the water-methanol tank. The solenoid fits in line between the pump and injection point and locks fluid in place when not in use adding safety and piece of mind to any injection kit. Can also be used to command a second stage of water-methanol with all VC-50 and Stage 3 equipped systems. Includes (2) 4AN fittings.

The Snow Performance High Flow Solenoid offers 100% safety for all injection systems utilizing rear mounted reservoirs, injection points under vacuum, or installs where the injection nozzle is lower than the water-methanol tank. The solenoid fits in line between the pump and injection point and locks fluid in place when not in use adding safety and piece of mind to any injection kit. Can also be used to command a second stage of water-methanol with all VC-50 and Stage 3 equipped systems. Includes (2) 1/4" Quick-Connect fittings.

Snow Performance fixed (100PSI) pressure regulator are designed for high-performance and demanding applications. These regulators can run your boost control solenoids, air shifter, or parachute launcher. The Billet Aluminum Regulators provide 100PSI preset, fixed flow pressures from a single pressure source. Each regulator is equipped with one high-pressure (bottle pressure) port and two low-pressure (100PSI) ports. These regulators are compatible with air, CO2, nitrogen, or nitrous oxide, making them an adaptable solution for a wide range of uses.

• Dual 1/8" NPT Outlets
• Fixed 100PSI

The Snow Performance Stage 3 Boost Cooler® brings true 2D mapped water-methanol injection delivery to your DI (direct fuel injected) and forced induction (turbocharged/supercharged) vehicle. The Stage 3 creates a 2D injection map based off boost and fuel pressure sensor input to deliver a extremely accurate amount of water-methanol when the engine needs it most. Bringing fuel pressure into the mix allows the injection curve to be extended past specific boost points for greater range/control. None invasive, the Stage 3 Boost Cooler® controller is designed to mount on the steering column or the dash so no additional gauge pods need to be purchased and functions as a boost gauge, water-meth controller and fuel system monitor all in one! Proven to reduce the air inlet temperature by up to 100 degrees and increase octane by 25 points for maximum HP and cooling . Comes with adjustable Stage 3 water-meth controller, 4AN fittings, and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.

• Adjustable Boost/Fuel Pressure Sensor Voltage Activated Progressive Water-Meth Delivery
• 300 PSI UHO Pump/SP Hypersonic Nozzles
• 100% Methanol Resistant
• Low Level MonitO-ring
• High Flow Check Valve
• Made In U.S.A.

The Snow Performance Stage 3 Boost Cooler® brings true 2D mapped water-methanol injection delivery to your DI (direct fuel injected) and forced induction (turbocharged/supercharged) vehicle. The Stage 3 creates a 2D injection map based off boost and fuel pressure sensor input to deliver a extremely accurate amount of water-methanol when the engine needs it most. Bringing fuel pressure into the mix allows the injection curve to be extended past specific boost points for greater range/control. None invasive, the Stage 3 Boost Cooler® controller is designed to mount on the steering column or the dash so no additional gauge pods need to be purchased and functions as a boost gauge, water-meth controller and fuel system monitor all in one! Proven to reduce the air inlet temperature by up to 100 degrees and increase octane by 25 points for maximum HP and cooling . Comes with adjustable Stage 3 water-meth controller, 1/4" High Temp Nylon line and easy to install quick-connect fittings.

• Adjustable Boost/Fuel Pressure Sensor Voltage Activated Progressive Water-Meth Delivery
• 300 PSI UHO Pump/SP Hypersonic Nozzles
• 100% Methanol Resistant
• Low Level MonitO-ring
• High Flow Check Valve
• Made In U.S.A.

The Snow Performance Stage 3 Boost Cooler® brings true 2D mapped water-methanol injection delivery to your EFI (electronic fuel injected) and forced induction (turbocharged/supercharged) vehicle. The Stage 3 creates a 2D injection map based off boost and fuel injector pulse width to deliver a extremely accurate amount of water-methanol when the engine needs it most. Bringing fuel injector pulse width into the mix allows the injection curve to be extended past specific boost points for greater range/control. None invasive, the Stage 3 Boost Cooler® controller is designed to mount on the steering column or the dash so no additional gauge pods need to be purchased and functions as a boost gauge, water-meth controller and fuel system monitor all in one! Proven to reduce the air inlet temperature by up to 100 degrees and increase octane by 25 points for maximum HP and cooling . Comes with adjustable Stage 3 water-meth controller, 4AN fittings, and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.

• Cleans all carbon build up out of your motor
• Reduce air intake temps out too 100 degrees
• Two-dimensional injection map
• Increase octane by 25 points
• Built in boost gauge
• New nozzle design
• Lower EGTS

The Snow Performance Stage 3 Boost Cooler® brings true 2D mapped water-methanol injection delivery to your EFI (electronic fuel injected) and forced induction (turbocharged/supercharged) vehicle. The Stage 3 creates a 2D injection map based off boost and fuel injector pulse width to deliver a extremely accurate amount of water-methanol when the engine needs it most. Bringing fuel injector pulse width into the mix allows the injection curve to be extended past specific boost points for greater range/control. None invasive, the Stage 3 Boost Cooler® controller is designed to mount on the steering column or the dash so no additional gauge pods need to be purchased and functions as a boost gauge, water-meth controller and fuel system monitor all in one! Proven to reduce the air inlet temperature by up to 100 degrees and increase octane by 25 points for maximum HP and cooling . Comes with adjustable Stage 3 water-meth controller, 1/4" High Temp Nylon line and easy to install quick-connect fittings.

• Cleans all carbon build up out of your motor
• Reduce air intake temps out too 100 degrees
• Two-dimensional injection map
• Increase octane by 25 points
• Built in boost gauge
• New nozzle design
• Lower EGTS

Decrease EGTs and increase HP in your diesel by 65HP+ in the most cost effective water-methanol injection kit on the market! Utilizing a adjustable boost pressure switch and dual nozzles to deliver precise amounts of water-methanol once 30 boost PSI has been reached (Boost Engagement Adjustable, 30 PSI Boost Hobbs Switch Included). Recommended for all high boost and competition diesels looking to increase HP while decreasing EGTs when on heavy throttle. Comes with easy to mount race ready 3QT tank, high flow check valve, quick-connect fittings, 300 PSI UHO Pump, and LED alert system.

• Up to 65 HP Increase!

Snow Performance has combined performance, quality, and easy installation in this new water-methanol injection system engineered specifically for all forced induction (supercharged/turbocharged) Dodge Challengers/Chargers with the 5.7 / 6.1 / 6.4 engine . Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! Complete with custom water-methanol injection throttle body spacer plate, braided stainless line, and 4AN fittings offering un surpassed reliability and ease of install. The Stage 2 uses a progressive VC-50 controller (ISO 9001 Manufactured) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. The VC-50 controller (52mm gauge) offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to match your OEM gauges or mix and match up to two colors. Fits all forced induction (supercharged/turbocharged) Dodge Challenger/Chargers with 5.7 / 6.1 / 6.4 engine.

• Achieve 116 Octane Quality Fuel From Pump Gas
• Cleans Engine Combustion Of Carbon Build Up
• Progressive Water-Methanol Injection
• Safely Run More Boost & Timing
• Cooler Denser Air Charge
• Made In USA

This Part Fits:

Snow Performance has combined performance, quality, and easy installation in this new water-methanol injection system engineered specifically for all forced induction (supercharged/turbocharged) 2016+ Gen 6 Chevy Camaro SS 6.2L LT1 engines. Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! Complete with custom water-methanol injection throttle body spacer plate, braided stainless line, and 4AN fittings offering un surpassed reliability and ease of install. The Stage 2 uses a progressive VC-50 controller (ISO 9001 Manufactured) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. The VC-50 controller (52mm gauge) offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to match your OEM gauges or mix and match up to two colors. Fits all forced induction (supercharged/turbocharged) 2016+ Camaro SS 6.2L.

• Achieve 116 Octane Quality Fuel From Pump Gas
• Cleans Engine Combustion Of Carbon Build Up
• Progressive Water-Methanol Injection
• Safely Run More Boost & Timing
• Cooler Denser Air Charge
• Made In USA

This Part Fits:

Snow Performance has combined performance, quality and easy installation in this new water-methanol injection system engineered specifically for 2010+ Ford F-150s equipped with the 3.5L EcoBoost engine. Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! Complete with custom water-methanol injection throttle body spacer plate, braided stainless line, and 4AN fittings offering un surpassed reliability and ease of install. The Stage 2 uses a progressive VC-50 controller (ISO 9001 Manufactured) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. The VC-50 controller (52mm gauge) offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to match your OEM gauges or mix and match up to two colors. Fits all 2010+ Ford F-150s equipped with the 3.5L EcoBoost engine.

• Achieve 116 Octane Quality Fuel From Pump Gas
• Cleans Engine Combustion Of Carbon Build Up
• Progressive Water-Methanol Injection
• Safely Run More Boost & Timing
• Cooler Denser Air Charge
• Made In USA

This Part Fits:

Snow Performance has combined performance, quality and easy installation in this new water-methanol injection system engineered specifically for forced induction (supercharged/turbocharged) 2011+ Ford 5.0 Coyote engines. Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! Complete with custom water-methanol injection throttle body spacer plate, braided stainless line, and 4AN fittings offering un surpassed reliability and ease of install. The Stage 2 uses a progressive VC-50 controller (ISO 9001 Manufactured) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. The VC-50 controller (52mm gauge) offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to match your OEM gauges or mix and match up to two colors. Fits all forced induction (supercharged/turbocharged) 2011+ Ford Mustang GTs equipped with the 5.0L Coyote engine.

• Achieve 116 Octane Quality Fuel From Pump Gas
• Cleans Engine Combustion Of Carbon Build Up
• Progressive Water-Methanol Injection
• Safely Run More Boost & Timing
• Cooler Denser Air Charge
• Made In USA

This Part Fits:

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler® water-methanol injection system is available for all forced induction applications (supercharged/turbocharged). The Stage 2 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability.The Stage 2 introduces the VC-50 Controller (ISO 9001 Manufactured). The VC-50 offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to your OEM gauges or mix and match up to two colors. Comes with 4AN fittings and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.

• Snow Performance OEM-Approved Extreme Environment 300 PSI UHO Water Methanol Pump
• 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
• Recommended For Street Driven Turbo and Centrifugal Supercharger Applications
• Snow Performance Running "S" Engraved Low Profile High Flow Check Valve
• Snow Performance Running "S" Engraved Low Profile Nozzle Holder
• Adjustable Progressive Water Methanol Engagement & Monitoring
• Snow Performance ACU-SEAL Water Methanol Compression Fittings
• Snow Performance Hyper-Sonic Water Methanol Nozzle
• Digital Boost Reading (1-50 PSI)
• Supports 1,000+ HP
• U.S.A. Made

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler® water-methanol injection system is available for all forced induction applications (supercharged/turbocharged). The Stage 2 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability.The Stage 2 introduces the VC-50 Controller (ISO 9001 Manufactured). The VC-50 offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to your OEM gauges or mix and match up to two colors. Comes with 4AN fittings and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.

• Snow Performance OEM-Approved Extreme Environment 300 PSI UHO Water Methanol Pump
• 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
• Recommended For Street Driven Turbo and Centrifugal Supercharger Applications
• Snow Performance Running "S" Engraved Low Profile High Flow Check Valve
• Snow Performance Running "S" Engraved Low Profile Nozzle Holder
• Adjustable Progressive Water Methanol Engagement & Monitoring
• Snow Performance ACU-SEAL Water Methanol Compression Fittings
• Snow Performance Hyper-Sonic Water Methanol Nozzle
• Digital Boost Reading (1-50 PSI)
• Supports 1,000+ HP
• U.S.A. Made

Unlock 50-70+HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2 Boost Cooler® water-methanol injection system is available for all forced induction applications (supercharged/turbocharged). The Stage 2 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability.The Stage 2 introduces the VC-50 Controller (ISO 9001 Manufactured). The VC-50 offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen you can tailor the controller to your OEM gauges or mix and match up to two colors. Comes with 4AN fittings and stainless steel braided line to mount pump/tank in engine bay of vehicle. For trunk mount options see Part# SNO-40014-BRD, SNO-40012-BRD.

• Snow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol Pump
• 100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)
• Recommended For Street Driven Turbo and Centrifugal Supercharger Applications
• Snow Performance Running "S" Engraved Low Profile High Flow Check Valve
• Snow Performance Running "S" Engraved Low Profile Nozzle Holder
• Adjustable Progressive Water Methanol Engagement & Monitoring
• Snow Performance ACU-SEAL Water Methanol Compression Fittings
• Snow Performance Hyper-Sonic Water Methanol Nozzle
• Digital Boost Reading (1-50 PSI)
• Supports 1,000+ HP
• U.S.A. Made