Designed for high-output Honda J35 V6 engines, these Eagle Specialty Products H-beam connecting rods provide the structural integrity required for forced induction, nitrous, or high-RPM naturally aspirated builds. Forged from certified 4340 chromoly steel, these rods offer a superior strength-to-weight ratio compared to factory cast components, helping to prevent rod failure under increased cylinder pressures.

• Fits Honda J35 V6 engines
• Forged from 4340 chromoly steel for maximum tensile strength
• H-beam design optimized for high-load applications
• Precision machined to exacting tolerances for consistent balance
• Complete set of 6 connecting rods

Fits Honda K24 engines specifically configured for "Long Rod" applications.

Eagle H-Beam connecting rods provide the structural integrity required for high-performance Honda K-series builds. Manufactured from certified forged 4340 chromoly steel, these rods are engineered to withstand the increased cylinder pressures and high-RPM stresses of turbocharged, supercharged, or high-compression naturally aspirated setups. The H-beam geometry offers an exceptional strength-to-weight ratio, ensuring the bottom end can handle significantly more load than factory components without adding excessive rotating mass.

Every rod is precision-machined and shot-peened to improve fatigue life and minimize stress risers. These Eagle rods serve as a critical upgrade for enthusiasts looking to push their K24 platform beyond the limits of OE hardware, providing a reliable foundation for your rotating assembly.

• Direct fit for Honda K24 Long Rod engine configurations
• Forged 4340 steel construction for maximum tensile strength
• Classic H-Beam design provides superior rigidity under load
• Shot-peened finish to increase resistance to fatigue and cracking
• Includes a complete set of 4 connecting rods

Fits Honda K20C 2.0L Turbo engines.

Eagle Specialty Products H-beam connecting rods provide the structural integrity required for high-performance Honda K20C builds. Forged from aircraft-quality 4340 steel, these rods are designed to withstand the extreme cylinder pressures and stresses of increased boost and higher RPM ranges that often exceed the limits of factory equipment. Each rod is shot-peened to increase fatigue life and heat-treated to ensure consistent material density and strength throughout the component.

• Manufactured from forged 4340 steel for superior tensile strength
• H-beam design for an optimal weight-to-strength ratio in forced induction applications
• Shot-peened finish to reduce stress risers and improve long-term durability
• Engineered specifically for the Honda K20C platform
• Includes a complete set of 4 matching connecting rods

Fits Honda K24 engines.

Eagle 4th Generation H-Beam connecting rods provide the essential structural foundation for high-performance Honda K24 engine builds. Manufactured from forged steel, these rods are designed to handle the increased cylinder pressures and higher RPM ranges found in turbocharged, supercharged, or high-compression naturally aspirated applications. The H-beam architecture delivers an excellent strength-to-weight ratio, reducing reciprocating mass to improve throttle response while maintaining the rigidity necessary to prevent rod deflection or failure under heavy loads.

• 4th Generation Eagle design
• Forged steel construction for maximum durability
• H-Beam profile for optimized weight and strength
• Engineered specifically for Honda K24 platforms
• Complete set of 4 rods

Fits Ford Focus models equipped with the ZETEC engine.

Eagle Specialty Products H-Beam connecting rods are engineered for the rigors of competition and high-output builds. Each rod is manufactured from a two-piece 4340 forged steel construction, providing superior strength-to-weight characteristics compared to factory cast components. To ensure maximum durability and fatigue resistance, the rods undergo a full CNC machining process followed by a shot-peening treatment.

These rods arrive as a weight-matched set, ready for installation. They come equipped with high-tensile ARP 2000 bolts to provide the clamping force necessary for high-RPM and forced induction applications. Whether building for the track or a high-performance street setup, these rods offer the structural integrity required for increased power levels.

• Material: Forged 4340 Chromoly Steel
• Design: H-Beam configuration
• Hardware: Included ARP 2000 3/8" bolts
• Finish: Fully machined and shot-peened
• Quantity: Set of 4 (Weight-matched)
• Manufacturer Part Number: CRS5483F3D

Fits 2006-2009 Mazdaspeed 3 and Mazdaspeed 6 equipped with the MZR engine and 22.5mm wrist pins.

These Eagle Specialty Products H-Beam connecting rods are engineered to provide the structural integrity required for high-performance and competition Mazdaspeed builds. Forged from high-tensile 4340 steel, these rods undergo a two-piece forging process and are fully machined to exacting tolerances. To enhance fatigue life and surface density, every rod is shot-peened, making them a reliable choice for forced induction and high-RPM applications.

This set comes equipped with ARP 2000 rod bolts, offering superior clamping force and power-handling capability compared to standard hardware. To ensure a balanced rotating assembly, these rods are packaged in weight-matched sets, significantly reducing engine vibration and bearing wear.

• Manufacturer Part Number: CRS5927M23D
• Material: Forged 4340 Steel
• Rod Design: H-Beam
• Wrist Pin Diameter: 22.5mm
• Hardware Included: ARP 2000 Bolts
• Finish: Fully machined and shot-peened
• Quantity: Weight-matched set of 4

Fits 1992-2009 Ford Crown Victoria, Mustang, Expedition, Explorer, F-150, and Thunderbird (4.6L Modular V8).

This Eagle cast crankshaft serves as a durable alternative and upgrade to an original equipment crankshaft for street-driven Ford 4.6L Modular V8 engines. It features 0.092-inch fillet radiuses for increased strength and fatigue resistance compared to stock components. Despite the improved radius, this crankshaft is designed to remain compatible with standard OE replacement bearings, making it a practical choice for engine refreshes and mild performance builds.

This component is specifically recommended for use in pump-gas, naturally-aspirated, non-competition road cars. It is internally balanced to ensure smooth operation within the factory RPM range.

• Manufacturer Part Number: 102813750
• Stroke: 3.750 in
• Engine Application: Ford 4.6L Modular V8
• Balance: Internal
• Fillet Radius: 0.092 in
• Material: Cast Steel

Fits Dodge 6.1L Hemi engines.

Eagle forged 4340 steel H-beam connecting rods are engineered for high-performance and competition environments. Forged from a two-piece design to optimize grain flow, these rods provide the structural integrity required for high-stress applications. Each rod undergoes a full machining process and is shot-peened to remove surface imperfections and improve fatigue resistance.

Sizing is held to exact tolerances for consistent performance across the entire set. These rods are delivered as a weight-matched set to ensure the balance of your rotating assembly and reduce engine vibration at high RPMs.

• Manufacturer Part Number: CRS6243H3D
• Material: Forged 4340 Steel
• Design: H-Beam
• Length: 6.243 inches
• Quantity: Set of 8 rods
• Finish: Fully machined and shot-peened
• Application: Recommended for competition use

Fits select 1997-2013 Cadillac CTS V, Chevrolet Camaro, Corvette, SSR, Trailblazer, Pontiac Firebird, and GTO (LS-based engines).

Eagle H-Beam connecting rods are engineered for the rigors of competition. These rods are manufactured from certified 4340 chromoly steel using a two-piece forging process that ensures superior grain flow and structural integrity. Every rod undergoes a full machining process followed by shot-peening to increase fatigue strength and relieve surface stress.

Sizing is held to extremely tight tolerances for consistent performance, and each set of eight is weight-matched to provide a balanced rotating assembly right out of the box. Designed specifically for LS applications requiring a .945-inch wrist pin, these rods provide a significant strength upgrade over factory components.

• Manufacturer Part Number: CRS6100M3D
• Material: Forged 4340 Chromoly Steel
• Design: Two-piece H-Beam forging
• Finish: Fully machined and shot-peened
• Wrist Pin Diameter: .945in
• Quantity: Weight-matched set of 8

Fits 2002-2004 Acura RSX Type-S (K20A2).

Eagle Specialty Products H-Beam connecting rods provide the structural integrity required for high-horsepower competition engines. These rods are manufactured from a two-piece 4340 steel forging to ensure optimal grain flow and then fully machined and shot-peened to eliminate stress risers. Each rod is equipped with high-tensile ARP 2000 bolts, providing superior clamping force and reliability under extreme cylinder pressures.

• Manufacturer Part Number: CRS5470K3D
• Material: Forged 4340 Chromoly Steel
• Design: H-Beam with two-piece forging
• Hardware: Includes ARP 2000 cap screws
• Finish: Fully machined and shot-peened surface
• Quality Control: Sold as a weight-matched set with sizing held to exact tolerances

Fits 1988-1995 Toyota Celica All Trac and MR2 Turbo (3SGTE).

Engineered for high-stress competition environments, these Eagle forged 4340 steel H-beam connecting rods provide the structural integrity required for forced induction and high-RPM 3SGTE builds. Each rod is manufactured from a two-piece forging, then fully machined and shot-peened to eliminate surface stress risers and improve fatigue life.

This set of four rods comes weight-matched to ensure rotating assembly balance and includes high-strength ARP 2000 cap screws for superior clamping force and reliability under heavy loads. Sizing is held to exacting tolerances for a precise fit on the crankshaft journals.

• Material: Forged 4340 chromoly steel
• Design: H-Beam for maximum rigidity
• Fasteners: Includes ARP 2000 bolts
• Finish: Fully machined and shot-peened
• Quantity: Weight-matched set of 4
• Manufacturer Part Number: CRS5428T3D

Fits select 1996-2000 BMW 323i/is/Ci, 328i/is/Ci, 528i, and Z3 models.

Eagle Specialty Products H-Beam connecting rods provide the structural integrity required for high-performance and competition BMW M52 engine builds. Each rod is manufactured from a two-piece forged 4340 steel process to ensure superior grain flow and durability. The surfaces are fully machined and shot-peened to relieve stress and improve fatigue life, while sizing is held to exacting tolerances for consistent bearing crush and clearance.

This set of six rods comes weight-matched to ensure rotating assembly balance. For maximum reliability under high cylinder pressures and high RPMs, these rods are equipped with premium ARP 2000 rod bolts.

• Material: Forged 4340 Steel
• Design: H-Beam (two-piece forging)
• Hardware: ARP 2000 Rod Bolts
• Finish: Fully machined and shot-peened
• Quantity: Weight-matched set of 6
• MPN: CRS5313B63D

Fits all 1990-2005 Mazda Miata models, including Base, LS, M Edition, and Mazdaspeed trims.

Eagle Specialty Products H-Beam connecting rods are designed for high-stress competition and forced induction applications. Each rod is manufactured from a two-piece 4340 steel forging to ensure superior grain flow and structural integrity. To maximize durability and fatigue life, these rods are fully machined and shot-peened. They are delivered as a weight-matched set, held to exacting tolerances to ensure balanced engine operation and simplified installation.

For increased power-handling capability and reliability under high RPMs, this set comes equipped with high-tensile ARP 2000 rod bolts.

• Manufacturer Part Number: CRS5233M3D
• Material: Forged 4340 Steel
• Design: H-Beam
• Includes: ARP 2000 Rod Bolts
• Quantity: Set of 4 weight-matched rods
• Surface Finish: Fully machined and shot-peened

Fits Chevrolet LS engines. These Eagle 4340 I-Beam connecting rods provide a reliable, high-strength solution for performance engine builds. Engineered from forged 4340 steel, these 6.125-inch rods are designed to provide an optimal balance of weight and structural integrity for demanding LS applications.

• Part Type: Connecting Rods
• Material: Forged 4340 Steel
• Rod Design: I-Beam
• Connecting Rod Beam Style: I-Beam
• Rod Length: 6.125 inches
• Quantity: Set of 8
• Manufacturer Part Number: FSI6125O

Eagle's I-Beam design ensures durability while maintaining the tolerances required for precision engine assembly. These rods are a direct replacement for standard length LS connecting rods in performance configurations.

Ensure the structural integrity of your rotating assembly with this Eagle Specialty Products replacement rod bolt set. Manufactured by ARP specifically for use in Eagle connecting rods, these fasteners provide the essential clamping force and fatigue resistance required for high-performance engine builds.

Constructed from ARP2000 high-strength alloy, these bolts are engineered to handle significantly higher tensile loads than standard hardware, making them a critical upgrade for high-RPM applications. Each bolt features a precision-machined 3/8-inch thread and a 1.5-inch under head length (UHL) to maintain proper torque and rod alignment. This kit includes a complete set of eight bolts.

• Manufacturer Part Number: EAG20060
• Material: ARP2000 Alloy
• Thread Size: 3/8 in.
• Under Head Length (UHL): 1.5 in.
• Socket Size: 7/16 in.
• Quantity: Set of 8 bolts

Fits select 1989-2004 Nissan 240SX, Altima, Axxess, D21, Frontier, Pickup, Stanza, and Xterra.

Eagle H-Beam connecting rods are engineered for competition use and high-load performance applications. These rods are manufactured from certified 4340 steel using a two-piece forging process that ensures consistent grain flow. Every rod is fully machined and shot-peened to increase fatigue life and eliminate surface stress risers. Sizing is maintained to exact tolerances to ensure a precise fit. Each weight-matched set includes high-strength ARP 2000 bolts for increased tensile strength and reliable power-handling capability.

• Forged from certified 4340 chromoly steel
• Two-piece forging process for superior structural integrity
• Fully machined and shot-peened surface finish
• Includes premium ARP 2000 cap screws
• Weight-matched for balanced engine operation

• Manufacturer Part Number: CRS6496N3D
• Material: Forged 4340 Steel
• Bolt Type: ARP 2000
• Quantity: Set of 4

Fits select 1992-2010 Audi and Volkswagen vehicles, including VR6-equipped models such as the Corrado SLC, Golf GTI VR6, R32, A3 Quattro, and TT Quattro.

Engineered for high-performance and competition use, these Eagle H-Beam connecting rods provide the structural integrity required for increased power levels. Each rod is manufactured from a two-piece forged 4340 steel process to ensure superior grain flow and durability. The surfaces are fully machined and shot-peened to eliminate stress risers and improve fatigue life, while sizing is held to exacting tolerances for a precise fit on the crankshaft journals.

This set of six comes as a weight-matched assembly, reducing engine vibration and ensuring consistent balance across all cylinders. To handle the increased tensile loads of high-RPM or forced induction applications, these rods are equipped with premium ARP 2000 bolts.

• Manufacturer Part Number: CRS6457V13D
• Material: Forged 4340 Steel
• Design: H-Beam with two-piece forging
• Hardware: ARP 2000 cap screws included
• Quantity: Set of 6 matched rods
• Finish: Fully machined and shot-peened

Engineered for high-stress competition environments, these Eagle 4340 H-Beam connecting rods provide the structural integrity required for performance Chrysler 5.7L and 6.1L Hemi builds. Each rod is manufactured from a two-piece 4340 forged steel process, ensuring superior grain flow and enhanced fatigue resistance compared to standard cast components.

To ensure maximum durability and precise fitment, these rods feature a fully machined and shot-peened surface finish. They are delivered as a weight-matched set and held to exacting tolerances to facilitate balanced engine operation and reliable power delivery under heavy loads. These rods are recommended for competition use and high-performance rebuilds.

• Material: Forged 4340 Steel
• Rod Length: 6.243 in
• Wrist Pin Size: 0.984 in
• Design: H-Beam
• Finish: Shot-peened and fully machined
• Quantity: Set of 8 rods
• Manufacturer Part Number: CRS6243R3D

Fits Chrysler 5.7L and 6.1L Hemi engines. These Eagle 4340 H-Beam connecting rods provide the structural integrity required for high-stress competition applications. Each rod is manufactured from a two-piece forging, fully machined to exacting tolerances, and shot-peened to improve fatigue resistance and longevity.

• Material: 4340 forged steel
• Length: 6.243 inches
• Wrist Pin Diameter: 0.945 inches
• Manufacturing: Shot-peened and fully machined surfaces
• Configuration: Set of 8 weight-matched rods
• Manufacturer Part Number: CRS6243C3D

Recommended for competition use, these H-Beam rods are weight-matched to ensure rotating assembly balance in high-performance Hemi builds.

Fits Ford 2.0L EcoBoost engines.

Eagle Specialty Products H-Beam connecting rods are engineered for the high-stress demands of competition use. These rods are manufactured from two-piece 4340 steel forgings to provide superior strength and durability compared to factory components. Each rod features a fully machined surface and is shot-peened to improve fatigue life and stress relief.

Sizing is held to exact tolerances to ensure a precise fit during engine assembly. These rods are sold as a weight-matched set of four, ensuring balanced rotational mass across all cylinders for improved high-RPM stability and engine longevity.

• Manufacturer Part Number: CRS6136E3D
• Material: Forged 4340 Chromoly Steel
• Design: H-Beam
• Finish: Fully Machined and Shot-Peened
• Quantity: Set of 4
• Application: Competition Use

Engineered for high-horsepower competition builds, these Eagle Specialty Products H-Beam connecting rods are forged from 4340 steel to handle the increased stresses of LS stroker applications. Each rod undergoes a two-piece forging process followed by full machining and a shot-peened finish to improve fatigue life and surface integrity. These rods are precision-sized to exacting tolerances and provided as a weight-matched set to ensure consistent rotating assembly balance.

This specific set (MPN: CRS6125O3DL19) is equipped with upgraded ARP L19 rod bolts. L19 is a premium steel alloy heat-treated to deliver significantly higher tensile strength than standard ARP2000 hardware, making these rods suitable for extreme cylinder pressures and high-RPM racing environments.

• Material: Forged 4340 Steel
• Design: H-Beam configuration for stroker applications
• Length: 6.125 in
• Hardware: ARP L19 Cap Screws
• Finish: Fully machined and shot-peened
• Quantity: Weight-matched set of 8
• Manufacturer Part Number: CRS6125O3DL19

Fits select 1997-2013 Cadillac, Chevrolet, and Pontiac models with LS-series engines, including Corvette, Camaro, GTO, and CTS-V.

Eagle Specialty Products H-Beam connecting rods are engineered for the rigors of competition use. Forged from certified 4340 chromoly steel, these rods undergo a two-piece forging process that optimizes grain flow for maximum structural integrity. Every rod is fully machined and shot-peened to improve fatigue resistance and eliminate surface stress risers.

This set is weight-matched within +/- 1 gram to ensure balanced engine rotating assembly performance and reduced harmonic vibration at high RPM. For superior reliability under high cylinder pressures, this set comes equipped with upgraded ARP 2000 bolts, providing the tensile strength needed for forced induction or high-horsepower naturally aspirated builds.

• Forged from high-tensile 4340 chromoly steel
• Precision machined and shot-peened for enhanced durability
• Equipped with high-strength ARP 2000 rod bolts
• Weight-matched within 1 gram per set
• Designed for high-performance and competition applications
• Manufacturer Part Number: CRS6125O3D2000

Fits select 1997-2013 Cadillac, Chevrolet, and Pontiac models with LS-series engines, including Corvette, Camaro, CTS-V, and GTO.

Engineered for high-stress competition environments, these Eagle H-Beam connecting rods provide the structural integrity required for performance builds. Each rod is manufactured from a two-piece 4340 steel forging, then fully machined and shot-peened to improve fatigue resistance and relieve surface stress. Sizing is held to exacting tolerances to ensure a precise fit on the crankshaft journals and piston pins.

These rods are delivered as a weight-matched set, ensuring your rotating assembly remains balanced for high-RPM reliability. Whether you are rebuilding a street-performance LS1 or a dedicated track LS3, these H-Beam rods offer a significant strength upgrade over factory cast components.

• Material: Forged 4340 Steel
• Design: H-Beam architecture
• Surface Treatment: Fully machined and shot-peened
• Quantity: Set of 8
• Application: Recommended for competition use
• Manufacturer Part Number: CRS6125O3D

Fits select 1984-1998 Nissan and Infiniti models (including 300ZX, Maxima, and J30) equipped with the VG30 engine series. This set of 6 Eagle Specialty Products H-beam connecting rods is engineered for high-performance builds and competition environments where increased horsepower and RPM demand superior tensile strength.

Manufactured from a two-piece 4340 steel forging, these rods undergo a rigorous manufacturing process to ensure reliability. Each rod is fully machined and shot-peened to reduce surface stress and improve fatigue life. To maintain engine balance and reduce vibration, these rods are delivered as a weight-matched set with sizing held to extremely tight tolerances. This kit (MPN: CRS6071N3D) comes equipped with genuine ARP 2000 bolts, providing the clamping force necessary for forced induction or high-compression naturally aspirated setups.

• Material: Forged 4340 Chromoly Steel
• Design: H-Beam profile for maximum rigidity
• Hardware: Includes high-tensile ARP 2000 rod bolts
• Finish: Fully machined and shot-peened
• Quantity: Set of 6 (weight-matched)
• Part Number: CRS6071N3D

Designed for the high-revving demands of competition use, these Eagle H-Beam connecting rods provide the structural integrity required for high-horsepower Honda F20C engine builds. Each rod is manufactured from a two-piece 4340 chromoly steel forging to ensure consistent grain flow and superior strength over factory cast units.

To maximize fatigue life, every rod is fully machined and shot-peened to eliminate surface stress risers. These rods are delivered as a weight-matched set, ensuring a balanced rotating assembly for smooth operation at high RPMs. For maximum clamping force and security under load, the set comes equipped with high-tensile ARP 2000 bolts.

• Engine Application: Honda F20C
• Material: Forged 4340 Chromoly Steel
• Design: H-Beam
• Included Hardware: ARP 2000 Rod Bolts
• Manufacturing: Fully Machined and Shot-Peened
• Weight-matched for balanced rotation
• Manufacturer Part Number: CRS6023A3D

Fits 1986-1992 Toyota Supra and Cressida models equipped with the 7M-GTE engine.

Eagle Specialty Products H-Beam connecting rods are designed for competition-level performance and high-horsepower applications. These rods are manufactured from two-piece 4340 forged steel, providing a significant strength advantage over factory components. Each rod is fully machined and shot-peened to increase fatigue life and relieve surface stress, ensuring reliability under extreme cylinder pressures.

To maintain rotating assembly balance, these rods are delivered as a weight-matched set. They come equipped with premium ARP 2000 bolts, offering the clamping force necessary for high-RPM and turbocharged builds.

• Material: Forged 4340 Steel
• Design: H-Beam
• Hardware: Included ARP 2000 Bolts
• Surface Treatment: Shot-peened and fully machined
• Quantity: Set of 6 rods
• Manufacturer Part Number: CRS5984T3D

This Eagle forged 4340 steel H-Beam connecting rod is engineered for Honda and Acura K24 engines, providing the structural integrity required for high-stress competition environments. Forged from a two-piece design, each rod undergoes a rigorous manufacturing process to ensure maximum durability under load.

Every rod is fully machined and shot-peened to reduce surface stress and improve fatigue life. Sizing is held to extremely tight tolerances, ensuring consistent fitment in high-performance engine builds. This single rod is ideal for specific replacement needs or custom configurations.

• Material: Forged 4340 chromoly steel
• Design: H-Beam profile for superior strength-to-weight ratio
• Finish: Fully machined and shot-peened surface
• Quantity: Single rod (1 Rod)
• Manufacturer Part Number: CRS5984K3D-1
• Application: Honda/Acura K24 engines

Note: Recommended for competition use. Please specify weight required when ordering to ensure proper rotating assembly balance.

Fits 2002-2010 Acura TSX and Honda Accord, CR-V, and Element models equipped with the K24 engine.

Designed for high-performance and competition applications, these Eagle H-Beam connecting rods are engineered to withstand the rigors of increased horsepower and torque. Each rod is manufactured from a two-piece forged 4340 steel process to ensure superior grain flow and structural integrity. The rods undergo a thorough machining process and are shot-peened to increase fatigue life and remove potential stress risers.

Eagle maintains tight tolerances on sizing and provides these rods in weight-matched sets for balanced engine operation. To maximize clamping force and rod-end stability under high RPMs, this set is equipped with premium ARP 2000 rod bolts.

• Forged from 4340 steel for maximum tensile strength
• H-Beam design optimized for load distribution and rigidity
• Center-to-center length: 5.984 inches
• Wrist pin diameter: 0.864 inches
• Shot-peened finish to improve durability
• Includes high-strength ARP 2000 rod bolts
• Weight-matched set of 4 rods
• Manufacturer Part Number: CRS5984K3D

Fits 2003-2005 Dodge Neon SRT-4 (2.4L).

Engineered for competition and high-horsepower applications, these Eagle H-Beam connecting rods provide the strength and durability required for forced induction and high-RPM use. Each rod is manufactured from a two-piece 4340 steel forging, then fully machined and shot-peened to improve fatigue life and relieve internal stresses. Sizing is held to exact tolerances for a precise fit on your 2.4L crankshaft journals.

These rods come equipped with high-tensile ARP 2000 bolts to ensure superior clamping force and reliability under extreme cylinder pressures. To maintain engine balance and reduce vibration, Eagle delivers these as a weight-matched set.

• Forged 4340 steel H-Beam construction
• Equipped with ARP 2000 rod bolts
• Fully machined and shot-peened surface
• Weight-matched set for rotating assembly balance
• Designed for competition use
• Manufacturer Part Number: CRS5945D3D

Fits select 1992-2009 Ford Crown Victoria, Expedition, Explorer, Mustang, Thunderbird, and E/F-Series trucks (4.6L).

Eagle forged 4340 steel H-Beam connecting rods are engineered for high-performance and competition applications where factory components reach their limits. Each rod is manufactured from a two-piece forging to ensure consistent grain flow and structural integrity. To improve fatigue life and eliminate stress risers, these rods feature a fully machined and shot-peened surface finish.

These rods are sized to exact tolerances and delivered as a weight-matched set, ensuring balanced rotating assembly performance. For maximum clamping force and high-RPM reliability, this set comes equipped with ARP 2000 series bolts. Whether you are rebuilding for the track or a high-output street build, these rods provide the durability required for forced induction or high-compression 4.6L setups.

• Manufacturer Part Number: CRS5933F3D
• Material: Forged 4340 Steel
• Design: H-Beam
• Hardware: ARP 2000 Bolts included
• Quantity: Set of 8 rods
• Sizing: Standard (STD)
• Finish: Fully machined and shot-peened